Login:
Stimmen - 1, Durchschnittliche Bewertung: 3 ( )

Anleitung American Dryer Corp., modell AD-230

Hersteller: American Dryer Corp.
Dateigröße: 4.12 mb
Dateiname:
Unterrichtssprache:en
Link zum kostenlosen Download Hinweise finden Sie am Ende der Seite



Anleitung Zusammenfassung


Proper cleaning of steam coils is necessary to prevent lint build-up between the fins. When cleaning the coil, be extremely careful not to bend the aluminum fins, which will also reduce airflow. If the fins air bent, straighten them by using a comb. Fin combs are available from local air conditioning supply houses. Regular cleaning will prevent lint build-up and blockage of the coil. 2 6 MONTHS Inspect and remove lint accumulation in the customer-furnished exhaust duct work system. Inspect exhaust back draft dampers to insure that they are not binding. Inspect and remove all lint accumula tion from in and around control box area including coin acceptors. Clean lint accumulation from around tumbler wrapper area. IMPORTANT^ The accumulation of lint in the exhaust duct work can create a potential fire hazard AS REQUIRED In cleaning and care of the cabinet, avoid using harsh abrasives. A product intended for the cleaning of appliances is recommended. B. ADJUSTMENTS SUGGESTED INTERVAL 6 MONTHS 6 MONTHS 6 MONTHS 12 MONTHS C. LUBRICATION The new bearings, idler bearings and tumbler bearing are sealed, lubrication is not necessary. w$£zm. Motor and drive belts should be examined. Cracked or seriously frayed belts should be replaced. Tighten loose belts when necessary, and check belt alignment. Complete operational check of controls and valves. Complete operational check of all safety devices (door switches, sail switch, burner and lint chamber thermostats.) Inspect bolts, nuts, screws non permanent gas connections, (unions orifices, etc.) electrical terminals, and grounding connections. 3 SECTION III TNSTATI ATION REQUIREMENTS Installation should be performed by competent technicians in accordance with local and state codes. In the absence of these codes, installation must conform to applicable American & National Standards. ANSI Z223.1 (LATEST EDITION) NATIONAL FUEL GAS CODE ANSI/NFPA NO. 70 (LATEST EDITION) NATIONAL ELECTRIC CODES A. ENCLOSURE AIR SUPPLY AND EXHAUST REQUIREMENTS NOTE: The following information is very brief and general. For a detailed description refer to the installation booklet for coin machines. Bulkheads and partitions around the dryer should be made of non-combustible materials. Allowances should be made for the opening and closing of the control door and lint door. Also, allowances should be made in the rear for ease of maintenance, (refer to installation manual for recommended distances and minimum allowances required.) When the dryer is operating, it draws in room air, heats it, passes this air through the tumbler, and exhausts it out the building. Therefore, the room air must be continually replenished from the outdoors. If the make up air is inadequate, drying time and drying efficiency will be adversely affected. Also, on gas machines Ignition problems and sail switch "fluttering" problems may result and on a electric machine, premature electric element failure may result. Air supply must be given careful consideration to insure proper performance of each dryer. IMPORTANT: Make up air must be provided from a source free of dry cleaning fumes. Make up air that is contaminated by dry cleaning fumes will result in irreparable damage to motors and other dryer components. Exhaust duct work should be designed and installed by a competent technician. Improperly sized duct work will create excessive back pressure, which will result in slow drying, increased use of energy, and shut down of the burner by the air flow (sail) switch. Refer to Installation Manual for more details. CAUTION: Improperly sized, installed or maintained (cleaned) exhaust duct work creates a potential fire hazard. 4 B. ELECTRICAL AND GAS REQUIREMENTS It is your responsibility to have all electrical connections made by a properly licensed and competent electrician to assure that the electrical installation is adequate and conforms with local and state regulations or codes. In the absence of such codes, all electrical connections, material, and workmanship must conform to the applicable requirements of the National Electric Code ANSI/NFPA NO. 79-(lattest edition). IMPORTANT: Failure to comply with these codes or ordinances, and or the requirements stipulated in this manual, can result in personal injury or component failure. The dryer installation must meet the American National Standard, National Fuel Gas Code ANSI Z223.1 (latest edition), as well as, local codes and ordinances and must be done by a qualified technician. NOTE: Undersized gas piping will result in ignition problems and slow drying and can create a safety hazard. The dryer must be connected to type of gas (natural or L.P.) indicated on the dryer data label. If this information does not agree with the type of gas available, contact the distributor who sold the dryer or contact the factory. The gas input ratings shown on the dryer data label are for elevations up to 2,000 feet, unless elevation requirements of over 2,000 f...

Dieses Handbuch ist für folgende Modelle:
Trockner - AD-235 (4.12 mb)

Bewertungen



Bewerten
Vorname:
Geben Sie zwei Ziffern:
capcha





Kategorien