Login:
Stimmen - 0, Durchschnittliche Bewertung: 5 ( )

Anleitung Hotpoint, modell DRYERS NWSR483

Hersteller: Hotpoint
Dateigröße: 329.02 kb
Dateiname:
Unterrichtssprache:en
Link zum kostenlosen Download Hinweise finden Sie am Ende der Seite



Anleitung Zusammenfassung


Use the Cycle Signal especially when drying fabrics like polyester knits and permanent press. These fabrics should be removed so wrinkles won’t set in. Drum Lamp (on some models) Before replacing the light bulb, be sure to unplug the dryer power cord or disconnect the dryer at the household distribution panel by removing the fuse or switching off the circuit breaker. Reach above dryer opening from inside the drum. Remove the bulb and replace with the same size bulb. 7 Operating Instructions Safety InstructionsConsumer Support Troubleshooting Tips About reversing the door. Reversing the Door Tools needed: Standard #2 Tape-tipped Phillips screwdriver putty knife 1 Open the door and remove the filler plugs opposite the hinges. With the door completely open, remove the bottom screw from each hinge on the dryer face. Insert these screws about half way into the TOP holes, for each hinge, on the opposite side (where you removed the filler plugs). Apply firm pressure to get the screw started in new holes. 2 Loosen top screw from each hinge on the dryer face half way. With one hand holding the top of the door and the other hand holding the bottom, remove the door from the dryer by lifting it UP and OUT. 3 Rotate the door 180°. Insert it on the opposite side of the opening by moving the door IN and DOWN until the top hinge and the bottom hinge are resting on the top screws inserted in step 1. 4 Remove the remaining screws from the side of the opening from which the door was removed. With these screws secure each hinge at the bottom. Tighten the 2 top screws of each hinge. Reinsert the plastic plugs on the side from which the door was removed. 8 Loading and using the dryer. Always follow the fabric manufacturer’s care label when laundering. Hotpoint.com Sorting and Loading Hints As a general rule, if clothes are sorted properly for the washer, they are sorted properly for the dryer. Do not overload. This wastes energy and causes wrinkling. Do not dry the following items: fiberglass items, woolens, Do not add fabric softener sheets once the load has rubber-coated items, plastics, items with plastic trim and become warm. They may cause fabric softener stains. foam-filled items. Bounce® Fabric Conditioner Dryer Sheets have been approved for use in all GE Dryers when used in accordance with the manufacturer’s instructions. The Exterior: Wipe or dust any spills or washing compounds with a damp cloth. Dryer control panel The Exhaust Duct: Inspect and clean the exhaust ducting at least once a year to prevent clogging. Care and Cleaning of the Dryer Consumer SupportTroubleshooting Instructions Fabric Care Labels and finishes may be damaged by some laundry pretreatment soil and stain remover products. Apply these products away from the dryer. The fabric may then be washed and dried normally. Damage to your dryer caused by these products is not covered by your warranty. The Lint Filter: Clean the lint filter before each use. Moisten your fingers and reach into the filter opening. Run your fingers across the filter. Have a qualified technician vacuum the lint from the dryer once a year. A partially clogged exhaust can lengthen the drying time. Follow these steps: Turn off electrical supply by disconnecting the plug from the wall socket. Disconnect the duct from the dryer. Vacuum the duct with the hose attachment and reconnect the duct. The Exhaust Hood: Check from the outside that the flaps of the hood move freely when operating. Make sure that there is no wildlife (birds, insects, etc.) nesting inside the duct or hood. 3 2 1 Below are fabric care label “symbols” that affect the clothing you will be laundering. WASH LABELS DRY LABELS Machine wash cycle Normal Permanent Press/ Gentle/ Do not wash Do not wring wrinkle resistant delicate Hand wash Water temperature Hot Warm Cold/cool (50°C/120°F) (40°C/105°F) (30°C/85°F) Tumble dry Dry Normal Permanent Press/ wrinkle resistant Gentle/ delicate Do not tumble dry Do not dry (used with do not wash) Heat setting High Medium Low No heat/air Specialinstructions Line dry/ hang to dry Drip dry Dry flat In the shade BLEACH LABELS Bleach symbols Any bleach Only non-chlorine bleach Do not bleach (when needed) (when needed) 9 Operating Instructions Safety InstructionsConsumer Support Troubleshooting Tips Loading and using the dryer. Always follow the fabric manufacturer’s care label when laundering. Venting the Dryer For the best drying performance the dryer needs to be properly vented. The dryer will use more energy and run longer if it is not vented to the below specifications. Carefully follow the details on Exhausting in the Installation Instructions. Use only rigid metal 4. diameter ductwork inside the dryer cabinet. Use only rigid metal or flexible metal 4. diameter ductwork for exhausting to the outside. Do not use plastic or other combustible ductwork. Use the shortest length possible. Do not crush or collapse. Avoid resting the duct on sharp objects. Venting must conform to l...

Dieses Handbuch ist für folgende Modelle:
Trockner - DRYERS NBXR463 (329.02 kb)
Trockner - DRYERS NVLR333 (329.02 kb)

Bewertungen



Bewerten
Vorname:
Geben Sie zwei Ziffern:
capcha





Kategorien