Stimmen - 2, Durchschnittliche Bewertung: 3.5 ( )

Hersteller: Clarke Dateigröße: 1008.49 kb Dateiname: Unterrichtssprache:

Blade, Rear - Gum Rubber 30067A Blade, Rear - Nitrile Solid 30081A Blade, Rear - Ribbed Orange 30085A Blade, Front - Ribbed Natural 30066A Blade, Front - Slit Grout 30079A Blade, Front - Ribbed Orange 30083A CLARKE TECHNOLOGY Operator's Manual -SCRUBTEC 743 and 751 Page -27 HOW TO CORRECT PROBLEMS IN THE MACHINE PROBLEM CAUSE ACTION There is no solution flow. The solution tank is empty. There is an obstruction in the solution hose or filter. The solution valve or electric wiring is damaged. The control module is defective. Fill the solution tank. Remove the obstruction from the hose or filter. Repair or replace the valve or the electric wiring. Replace control module The solution flow does not stop. The solution valve is open. The solution valve or wiring is damaged. The solution valve is dirty There is a damaged seat and washer in the solution valve. The control module is defective. Close or Clean the solution valve. Repair or replace the valve and the wiring. Clean the solution valve. Replace the seat and washer. Replace control module. The machine does not remove all the water from the floor. The squeegee is up. The squeegee tilt is not correct. The recovery tank is full. The screen filter is dirty. There is an obstruction or damage in the squeegee or squeegee hose. The vacuum motor is not running. The squeegee hose is disconnected, or damaged The squeegee blade is damaged, worn, or incorrectly installed. The gaskets on the cover of the recovery tank are damaged. Lower the squeegee. To adjust, see the section titled "How to Adjust the Squeegee". Drain the recovery tank. Clean the screen filter. Remove the obstruction or repair the damage. Check for tripped breaker. Have an authorized service person make repairs. Check and connect hose. Turn or replace the squeegee blade. Correctly install the squeegee blade. Replace the gaskets. The batteries do not give the normal running time. The battery terminals are dirty or damaged. The electrolyte level is too low. The batteries are not fully charged. The charger is damaged. The battery is defective. The batteries are disconnected. Brush is in heavy scrub setting. Clean the terminals and connectors. Replace the damaged cables. Charge the batteries. Add distilled water to each cell and charge the batteries. Charge the batteries for a full 16 hour charge. Have an authorized service person repair the charger. Check voltage of each cell while discharging. Connect the batteries. Adjust Pressure. Page -28-CLARKE TECHNOLOGY Operator's Manual -SCRUBTEC 743 and 751 PROBLEMPROBLEMACTION The cleaning is not even. The scrub brush or pad is worn. There is damage to the brush assembly, caster or the solution valve. The brush motor is not running The solution level is low. Replace the scrub brush or pad. Have an authorized service person make the needed repairs. Check for tripped breaker. Reset. Check for loose connections. Fill the solution tank. NOTE: If the problem continues consult an authorized service person. The machine does not run. The machine loses power. Key or switch is off. Batteries are disconnected. Battery terminals are dirty. Batteries are discharged Reset the circuit breaker. Turn key or switch on. Check the battery connections. Check battery meter and recharge NOTE: If the problem continues consult an authorized service person. CLARKE TECHNOLOGY Operator's Manual -SCRUBTEC 743 and 751 Page -29 NOTE Page -30-CLARKE TECHNOLOGY Operator's Manual -SCRUBTEC 743 and 751 SCRUBTEC 743 S SCRUBTEC 743 L SCRUBTEC 743 LSCRUBTEC 743 LSCRUBTEC 743 LSCRUBTEC 743 LSCRUBTEC 743 L SCRUBTEC 751 S SCRUBTEC 751 SSCRUBTEC 751 SSCRUBTEC 751 SSCRUBTEC 751 SSCRUBTEC 751 S SCRUBTEC 751 L SCRUBTEC 751 LSCRUBTEC 751 LSCRUBTEC 751 LSCRUBTEC 751 LSCRUBTEC 751 L SCRUBTEC 743 S C SCRUBTEC 743 S CSCRUBTEC 743 S CSCRUBTEC 743 S CSCRUBTEC 743 S CSCRUBTEC 743 S C SCRUBTEC 743 L C SCRUBTEC 743 L CSCRUBTEC 743 L CSCRUBTEC 743 L CSCRUBTEC 743 L CSCRUBTEC 743 L C Section II Parts and Service Manual (70900A) U.S. Patent No. 6,105,192; No. 6,557,207; No. 6,760,947 CLARKE TECHNOLOGY Operator's Manual -SCRUBTEC 743 and 751 Page -31 CLARKE TECHNOLOGY SCRUBTEC 743 and 751 CLARKE TECHNOLOGY Final Assembly 5/05 1 2 3 4 5 6 7 2 8 9 11 12 2 3 13 14 12 32 16 15 12 10 Page -32-CLARKE TECHNOLOGY Operator's Manual -SCRUBTEC 743 and 751 CLARKE TECHNOLOGY SCRUBTEC 743 CLARKE TECHNOLOGY and 751 and 751and 751and 751and 751and 751 Final Assembly Parts List 5/05 Ref. # Part No. Description Qty 1 Page 32 Recovery Tank Assembly 1 2 980651 Washer, Flat 5/16" 8 3 80212A Screw, M8 x 1.25 x 35mm Hex Head 4 4 Page 34 Solution Tank Assembly 1 5 Page 48 Rotary Disk Head Assembly Option 1 6 Page 46 Cyl. Head Asm. Option (L17 Cyl. model only) 1 7 Page 44 Frame Assembly 1 8 80197A Screw, M8 x 1.25 x 20mm Hex Head 4 9 980652 Washer, Lock 5/16" 4 10 Page 42 Squeegee Assembly 1 11 Page 40 Squeegee Lift Assembly 1 12 80179A Screw, M6 x 1 x 15mm Pan Head 6 13 Page 38 Control Housing Assembly 1 14 Page 36 Electrical Assembly 1 15 30334...

Herunterladen

Geben Sie zwei Ziffern: