Stimmen - 4, Durchschnittliche Bewertung: 4.5 ( )

Hersteller: AEG Dateigröße: 335.24 kb Dateiname: 217610en.pdf Unterrichtssprache:

Press the W SPECIAL CARE button if you are drying delicate fabrics. We recommend that you check the care symbols before purchasing your clothes. • Wool, down feathers Do not dry any woollen items in the dryer! Danger of becoming felted! Dry down feathers in the dryer only when you find a corresponding care symbol. • Fabrics sensitive to temperatures Dry fabrics sensitive to temperatures (such as acrylic or viscose) and textiles with the care label S with the W SPECIAL CARE button activated. • Cotton jersey, hosiery Cotton jersy and hosiery have a tendency to shrink! Do not dry these fabrics excessively. High quality brand name products are less likely to shrink. • New coloured textiles Do not dry new coloured textiles together with light-coloured laundry. This could lead to discolorations! Cleaning and maintenance Cleaning and maintenance Cleaning the condenser 1 Important! It is essential to clean the condenser after every thirty drying processes. Otherwise your dryer might suffer damage. Furthermore, energy consumption is greater when the condenser is covered with fluff. 0 Open the fill-in door. 0 Press on the two tabs to unlatch and take off the base mask. 0 Turn the two securing disks through a quarter turn each outwards. 0 Pull the condenser out of the base by the handle. 0 Clean the condenser, best with a handheld brush or by rinsing-through strongly with a hand-held shower head. The water removal slits on the rear of the condenser must be free too. 1 Important! Do not use any sharply pointed objects to clean the condenser. They could make it leak. 0 Reinsert and latch the condenser again (turn each one of the two securing disks through a quarter turn inwards). The legend "top – oben – en haut" must be at the top. 0 Re-mount the base mask. 1 Important! The dryer must not be operated without condenser. Cleaning and maintenance Cleaning the filter area A small amount of fluff reaches the area around the filter in spite of the fluff filter. Therefore you should clean the entire filter area from time to time, but at least every three months. 0 Remove the fluff filter. 0 Hold the filter lid by the top and pull it forwards until it is released from both holders. 0 Remove the fluff from the entire filter area – preferably with a vacuum cleaner. 0 Press both pins of the filter lid into the holders on the door until they click in. 0 Reinsert the fluff filter. 0 Press against the filter lid until it clicks into the lock. Clean the drum 1 Attention! Do not clean the stainless steel drum with abrasive detergents or steel wool! 0 Wipe the inside of the drum and the drum fins with a standard household detergent (e.g. vinegar solution). Cleaning the panel and operating parts 1 Attention! Do not use household furniture polish or aggressive detergents. 0 Wipe over the panel and operating parts with a damp cloth. Only use warm water. Troubleshooting Troubleshooting In the event of a malfunction try to solve the problem yourself using the information below. If you call out the customer service to solve one of the problems listed here or due to incorrect operation, a charge will be made for the visit of the service engineer even during the warranty period. Problem Possible cause Remedy The dryer is not working The drying result is unsatisfactory Electric mains plug not Connect the mains plug connected X STARTbutton not Press the X START pressed button No program set Set a program Fill-in door open Close the fill-in door Check the fuse or Fuse blown or automatic automatic circuit breaker. circuit breaker in the Get an electrician to repair fusebox (house electrical any faults in the house installation) defective electrical installation. Set a different (time) Wrong program selected program for the next drying process Fluff filter clogged Clean the fluff filter Heat exchanger covered Cleaning the heat with fluff exchanger Keep to the Incorrect amount of recommended amount of laundry filled-in laundry to be filled-in Laundry drained insuffi- Drain the laundry ciently before drying adequately Ventilation slits in the Clear the ventilation slits base region covered-up in the base region Deposit on the inside Clean the inside surface surface of the drum or on of the drum and the the drum ribs drum ribs Troubleshooting Problem Possible cause Remedy Heat exchanger covered Cleaning the heat The drying process takes with fluff exchanger unusually long Fluff filter clogged Clean the fluff filter The fill-in door cannot be closed Fluff filter not inserted and/or filter lid not latched Insert the fluff filter and/ or let the filter lid latch into position The drum illumination is not Program selector set to OFF Turn the program selector to the setting LIGHT or set a drying program functioning Filament bulb defective Replace the filament bulb (see next section) Display Z EMPTY WATER is Empty the condensate Condensate container full lit container Z EMPTY WATER indicator illuminated, even though the container has already been emptied Fo...

Herunterladen

Geben Sie zwei Ziffern: