Stimmen - 3, Durchschnittliche Bewertung: 4.7 ( )

Hersteller: AEG Dateigröße: 403.95 kb Dateiname: 981082EN.pdf Unterrichtssprache:

It is not due to excessive wear caused by the dryer. All fabric looses fluff when drying but it goes un-noticed in the air. In a tumble dryer it simply collects in the filter. If necessary the filters can be cleaned under running water using a brush. In this case, remove the filter in the door opening as per picture (it can be positioned with the tongue facing to the left or to the right). Cleaning the drum Warning! Do not clean the stainless steel drum with abrasive detergent or steel wool. Wipe the inside of the drum and the drum paddles with a standard household detergent (e.g. vinegar solution). Cleaning the panel and the controls Warning! Do not use household furniture polish or abrasive detergents. Wipe the panel and the controls with a damp cloth only. Use only warm water. 21 Cleaning and care Smoething not working? Something not working? If a problem occurs, you can try to solve it yourself following the instructions below. If you call out an engineer when one of the following problems occurs, or to repair a fault due to incorrect use, the call-out will be charged even if requested within the guarantee period. Problem Possible cause Remedy Mains plug disconnected Plug in mains plug Select programme No programme selected Loading door open Close loading door The drier is not working properly Check fuse or residual current Fuse or residual current cir circuit breaker. cuit breaker in fuse box Faults can be eliminated by an (domestic installation) faulty electrical engineer Select another (time) programme for the next drying cycle Wrong programme selected Clean lint filter Lint filter blocked Observe recommended filling The drying results are Wrong filling quantity quantity not satisfactory Laundry not sufficiently dried Pre-dry laundry sufficiently Deposit on the drum inner Clean drum inner surface and surfaceor on the drum ribs drum ribs Smoething not working? Problem Possible cause Remedy The drying cycle exceptionally takes a long time The loading door cannot be closed The drier ends the drying cycle automatically: END indicatoris illuminated shortly after programme start Vented air transport disrupted Straighten N- air venting hose and/or clean air venting ducts Lint filter blocked Clean lint filter Lint filter not installed and/or filter lid not locked in position Install lint filter and/or lock filter lid in position Too little or too dry laundry loaded for selected programme Select time programme or higher drying level (for instance EXTRATROCKEN instead of STARKTROCKEN) The drying cycle exceptionally takes a long time. 4,5 hours after starting the drying cycle: END indicator is illuminated - drying cycle is aborted - programme run indicator flashes SCHON- button depressed and filling quantity too large Check programme selection: only use SCHON -button for laundry quantities up to 3 kg. Clean lint filter. Reduce filling quantityFilling quantity too large Pre-dry laundry more thorougly Laundry too wet If these operating instructions do not offer sufficient advice to eliminate a specific fault, please contact our customer service. Technical specifications Height x Width x Depth 85x60x57 cm Depth with the door open 107 cm Height adjustment 6 mm Empty weight 32 kg approx. Load (according to the programme) max. 6 kg (Different load sizes in some countries are due to different measuring methods) Use Domestic Permissible ambient temperature +5°C to +35°C This appliance complies with the following EC directives: -73/23/EEC of 19/2/1973 “Low voltage directive” -89/336/EEC of 3/5/1989 “EMC directive” including modification directive 92/31/EEC. Electrical connection Specifications concerning the power supply are indicated on the rating plate. The rated voltage and the type of current stated on the plate must correspond to those which exist where the dryer is installed. Also refer to the rating plate for the type of fuse required. Permanent connection must be carried out only by a qualified engineer. Warning! THIS APPLIANCE MUST BE EARTHED. The manufacturer declines any liability should this safety measure not be observed. Before switching on, make sure the electricity supply voltage is the same as that indicated on the appliance’s rating plate. (See picture on page 11). The appliance is supplied with a 13amp plug fitted. In the event of having to change the fuse in the plug supplied, a 13amp ASTA approved (BS1363A) fuse must be used. Should the plug need to be replaced for any reason, proceed as described below. The wires in the mains lead are coloured in accordance with the following code: Green and Yellow - Earth Blue - Neutral Brown - Live The wire coloured green and yellow must be connected to the termi nal marked with the letter «E» or by the earth symbol or coloured green and yellow. The wire coloured blue must be connected to the terminal «N» or coloured black. The wire coloured brown must be connected to the terminal marked «L» or coloured...

Herunterladen

Geben Sie zwei Ziffern: