Stimmen - , Durchschnittliche Bewertung: ( )

Anleitung Sears, modell 9709

Hersteller: Sears
Dateigröße: 1.52 mb
Dateiname:

Unterrichtssprache:

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

The door will hang in place while you insert and tighten the remaining 4 screws. NOTE: Two or more people may be needed to reattach the dryer door. A B C A. Dryer door B. Dryer front panel C. Insert this hinge screw first. 5. Close the door and check that it latches securely. 6. Check for fingerprints on the glass. Clean the glass if necessary. Complete Installation 1. Check that all parts are now installed. If there is an extra part, go back through the steps to see which step was skipped. 2. Check that you have all of your tools. 3. Check the dryer’s final location. Be sure the vent is not crushed or kinked. 4. Check that the dryer is level. See “Level Dryer.” WARNING Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. 5. Plug into a grounded 3 prong outlet. Turn on power. 6. Remove any protective film or tape remaining on the dryer. 7. Dispose of/recycle all packaging materials. 8. Set the decorative mat in place on top of the dryer, if desired. NOTE: Check that the top of the dryer and the bottom of the mat are clean. 9. Read “Dryer Use.” 10. Wipe the dryer drum interior thoroughly with a damp cloth to remove any dust. 11. Select a Timed Dry heated cycle, and start the dryer. Do not select the Air Only Temperature setting. If the dryer will not start, check the following: ¦ Dryer is plugged into a grounded 3 prong outlet. ¦ Electrical supply is connected. ¦ Household fuse is intact and tight, or circuit breaker has not tripped. ¦ Dryer door is closed. 12. When the dryer has been running for 5 minutes, open the dryer door and feel for heat. If you feel heat, cancel cycle and close door. If you do not feel heat, turn off the dryer and check that the gas supply line shutoff valve is open. ¦ If the gas supply line shutoff valve is closed, open it, then repeat the 5-minute test as outlined above. ¦ If the gas supply line shutoff valve is open, contact a qualified technician. 15 DRYER USE Starting Your Dryer WARNING Explosion Hazard Keep flammable materials and vapors, such as gasoline, away from dryer. Do not dry anything that has ever had anything flammable on it (even after washing). Failure to follow these instructions can result in death, explosion, or fire. WARNING Fire Hazard No washer can completely remove oil. Do not dry anything that has ever had any type of oil on it (including cooking oils). Items containing foam, rubber, or plastic must be dried on a clothesline or by using an Air Cycle. Failure to follow these instructions can result in death or fire. Follow these basic steps to start your dryer. Please refer to specific sections of this manual for more detailed information. 1. Clean lint screen before each load. See “Cleaning the Lint Screen.” 2. Place laundry in dryer and shut door. 3. Press the POWER button. Then rotate the dial or press a Timed Cycles button to select the desired Auto or Timed Cycle. The preset modifiers for Auto Cycles or Timed Cycles will glow green. The estimated or actual cycle time (in minutes) will show in the display. To use an Auto Cycle NOTE: A light next to each feature will glow green when the feature is selected. ¦ Select an Auto Cycle. ¦ Select DRYNESS LEVEL to adjust how dry you want the load. As the cycle runs, the control senses the dryness of the load and adjusts the time automatically for the selected dryness level. NOTE: Most loads may be dried using Normal dryness level, which is shown in bold letters on your control panel. Normal is the energy preferred dryness level and will use the least energy. ¦ Select the desired Options. To make changes during an Auto Cycle: ¦ Press STOP once. ¦ Adjust Dryness Level. NOTE: Dryness Level selections can be made only while using Auto Cycles. You can select a different dryness level, depending on your load, by pressing Dryness Level and choosing More Dry, Normal or Less Dry. Selecting More Dry, Normal or Less Dry automatically adjusts the sensed time needed. How Auto Dry works SmartHeat™ improves drying performance with Auto Moisture Sensing Plus, which advances the cycle as moisture is extracted from clothing. A thermistor (electronic temperature sensor) and moisture sensing strips in the dryer drum help measure the amount of moisture in the clothes as they tumble. An electronic control determines the load type to help save time, avoid overdrying, and increase the accuracy of the end dryness level. After the first 5 minutes of an automatic cycle, the estimated time display will adjust based on the approximate load size, cycle, dryness level selected and amount of moisture left in the clothes. When the clothes have reached approximately 80% of the dryness level selected, the estimated time display will adjust again, showing the final drying time. Auto Moisture Sensing Plus takes the guesswork out of drying time and enhances fabric care. To use a T...