Stimmen - 3, Durchschnittliche Bewertung: 4.7
(
)
)
|
Anleitung Zusammenfassung
E. g. in case of STORAGE programme the following status icons are visible: . Current cycle progress is marked by flashing dash under status icon. When appropriate part of drying cycle is accomplished dash becomes steady and appears flashing under next status icon. Changing programme To change a programme which has been selected by mistake once the programme has started, first turn the programme selector to OFF and then reset the programme. The programme can no longer be changed directly once the programme has started. If nevertheless there is an attempt to change the programme on the programme knob, the programme progress display and the maintenance indicators flash. If an option button (excluding the BUZZER button) is pressed, Err appears in the multidisplay. The drying programme is not however affected by this (laundry protection). Putting in extra items or taking items out before end of programme 1. Open loading door. Daily use 21 WARNING! Laundry and drum can become hot. Risk of burns! 2. Load or remove laundry items. 3. Close loading securely. Lock must audibly lock. 4. Press the START PAUSE button to continue the drying cycle. Drying cycle complete / removing laundry Once the drying cycle is complete, display shows a blinking "0", under anti-crease icon appear dash. If the BUZZER button has been pressed, an acoustic signal sounds intermittently for about one minute. The drying cycles are automatically followed by an anti-crease phase which lasts around 30 minutes. The drum rotates at intervals during this phase. This keeps the laundry loose and free of creases. The laundry can be removed at any time during the anti-crease phase. (The laundry should be taken out towards the end of the anti-crease phase at the latest to prevent creases from forming.) If LONG ANTICREASE function has been selected, the anti-crease phase is lengthened by 60 minutes. 1. Open door. 2. Before removing the laundry, remove fluff from the micro-fine filter. It is best to use a damp hand for this purpose. (See “Care and cleaning” chapter.) 3. Remove laundry. 4. Turn the programme selector to OFF. After each drying cycle: -Clean the micro-fine filter and fine filter -Drain the condensed water container (See chapter “Care and cleaning”.) 5. Close the door. Care and cleaning Cleaning fluff filter The filters collect all the fluff which accumulates during drying. To ensure that the dryer works perfectly, the fluff filters (micro-fine filter and fine strainer) must be cleaned after every drying cycle. The warning icon is on to remind you this operation. CAUTION! Never operate the dryer without fluff filters or with damaged or blocked fluff filters. 1. Open loading door 2. Use a damp hand to clean the micro- fine filter, which is built into the lower part of the loading aperture. 3. After a period of time, a patina due to detergent residue on laundry forms on the filters. When this occurs, clean the filters with warm water using a brush. Remove the filter from the door pulling it out. It can be positioned with the tooth facing to the left or to the right). After cleaning do not forget to put it back. 22 Care and cleaning 4. Push down unlock button on large mesh filter. Large mesh filter jumps up. 5. Take out fine strainer. 6. Remove fluff from fine strainer. It is best to use a damp hand for this purpose. Clean the entire filter area The strainer area does not have to be cleaned after every drying cycle, but should be checked regularly and cleaned of fluff if necessary. 7. To do this, grip the top of the large mesh filter and pull it forwards until it comes loose from the two brackets. 8. Remove fluff from the entire filter area. It is best to use a vacuum cleaner for this purpose. 9. Press both journals of the large mesh filter into the brackets on the loading door until they snap into place. 10. Re-insert fine strainer. Care and cleaning 23 24 24 Care and cleaning 11. Press against the large mesh filter until it locks into the interlock. If the fine strainer is not fitted, the large mesh filter will not snap into place and the loading door cannot be closed. Cleaning the door seal Wipe the door seal with a damp cloth immediately after the drying cycle has finished. Emptying the water reservoir Empty the water reservoir after every drying cycle. If the water reservoir is full, an active programme will break off automatically and the empty container icon on the display will light up. In order to continue the programme, the water reservoir must first be emptied. WARNING! The condensed water is not suitable for drinking or for preparing foodstuffs. 1. Take out drawer containing condensed water container completely 1 and pull up the condensed water container’s drainage pipe as far as it will go 2. 12 Care and cleaning 25 2. Pour condensed water out into a basin or similar receptacle. 3. Slide outlet connections in and refit water reservoir. If the programme has been interrupted as a result of the water reservoir being full: Press the START...