Stimmen - 1, Durchschnittliche Bewertung: 4 ( )

Hersteller: Admiral Dateigröße: 2.8 mb Dateiname: 53-4623_AD-1Dryer.pdf Unterrichtssprache:

If care label instructions are not available, use the following information as a guide. Dryer Rack Use the removable drying rack for boots, sneakers, fragile sweaters, nylon stockings – any items that might be damaged by tumbling. To use the rack: 1. Position L-shaped legs against round inset at back of dryer. 2. Rest the two front legs on either side of the lint screen. 3. Check to see that the rack is securely in position. 4. Place items to be dried on top of the rack. Allow space for air to circulate. Items should not hang over the edge, between the supports, or touch any other part of dryer. NOTE: The rack does not move, but the drum rotates around the rack. 5. Close dryer door. 6. Use TIME DRY CYCLE. Select temperature Regular, Delicate or Air Fluff, depending on the item. 7. Some items may need to be rotated from front to back or refolded to dry inner layers – check periodically. 8. To remove rack, simply grasp sides with hands and lift out. Note • Do not place hands in dryer while drum is rotating. Care & Cleaning Control Panel Clean with a soft, damp cloth. Do not use abrasive substances. Tumbler Remove any stains (such as crayon, ink pen or fabric dye) with soap and water. Then tumble clean old towels or rags to remove any excess stain. Cabinet Wipe off any marks with soap and water. Use an appliance wax once a year if desired. Dryer Exhaust System Inspect and clean once a year to maintain optimum performance. The outside exhaust hood should be cleaned more frequently to ensure proper operation. (Refer to the Installation Instructions for more information.) Replacing the Drum Light (select models) 1. Unplug or disconnect the dryer from the power supply. 2. Lift top of dryer by inserting a putty knife under top, 4" in from each side. 3. Rotate bulb holder to vertical position before removing bulb. 4. Push bulb down and rotate counterclockwise to remove. 5. Replace with a 25 watt, 115/125 volt twist lock utility light Part No. 53-0570 or equivalent. Place bulb in socket, push down and rotate clockwise. 6. Rotate bulb holder to horizontal position. 7. Place top of dryer back in original position. Make sure metal tabs hold top in place. 8. Reconnect dryer to power supply. Dryer Exhaust Tips WARNING Plastic or nonmetal flexible duct presents a potential fire hazard. Do Read the installation instructions and the use and care guide. Do annually. Let your dryer exhaust the air easily. Do Use 4" diameter rigid metal duct. Tape all joints, including at the dryer. Never use lint-trapping screws. Do Keep duct runs as straight as possible. Do Clean all old ducts before installing your new dryer. Be sure vent flap opens and closes freely. Inspect and clean the exhaust system Don’t Let a poor exhaust system cause slow drying. Don’t Restrict your dryer with a poor exhaust system. Don’t Use plastic, thin foil, or non-metal flexible duct. Don’t Use longer than necessary duct runs with many elbows. Don’t Allow crushed or clogged ducts and vent. Troubleshooting Doesn’t Run • Be sure the door is shut. • Is the electrical cord plugged in? • Has a fuse blown or the circuit breaker tripped? • Push the control dial in again if the door was opened during the cycle. Doesn’t Heat • Has a fuse blown or the circuit breaker tripped? • Select a heat setting, not air fluff. • Check that the gas supply is on for gas dryers. • Clean the lint filter and exhaust duct. • Dryer timer may have moved into the cool-down portion of the cycle. Doesn’t Dry • Check all of the above, plus . . . Properly • Check the exhaust hood outside the house, does it open and close freely? • Check exhaust system for lint buildup. Ducting should be inspected and cleaned annually. • Use rigid 4" metal exhaust duct. • Do not overload. 1 wash load = 1 dryer load. • Sort heavy items from lightweight items. • Large, bulky items like blankets or comforters may require repositioning to ensure even drying. • Check the washer to be sure it is draining properly to extract water from the load. • Clothes load is too small to tumble properly. Add a few towels. Is Noisy • Check the load for objects such as coins, nails, etc. Remove promptly from dryer. • It is normal to hear the dryer gas valve or heating element cycle on and off during the drying cycle. • The dryer should be level and installed on a solid floor. • A clicking noise may be the timer advancing. • It is normal for the dryer to hum due to the high velocity of air moving through the dryer drum and exhaust system. Control Knob • This is normal operation for an Auto Dry cycle, especially at the beginning of cycle. Once Advances the load begins to dry, the control knob will start to advance. The rate of advancement will Slowly be slow at the beginning of the cycle because there is more moisture in the load. As the load becomes more dry, the control knob will advance more quickly. Dries Unevenly • Seams, pockets and other similar heavy areas may not be completely dry when the rest of the load has reached the selec...

Herunterladen

Geben Sie zwei Ziffern: