Stimmen - 3, Durchschnittliche Bewertung: 4.7
(
)
)
|
Anleitung Zusammenfassung
close to the baby monitor can units. cause interference. Receiving signals from a Both systems are using the same Switch channels. different baby monitor. frequencies System check light flashing/ Units are out of range or there is Move parent units closer to baby system check alarm activated interference from another FM unit to restore the link. Remove source the other FM source. 8 IFUSC369ENbk.p65 5 GETTING THE UNITS READY FOR USE Baby unit Connect the AC power adapter (power supply socket (A-5) of the Baby If you want to use batteries, remove the Insert four 1.5V, AA batteries (not included; we recommend non-chargeable Philips Alkaline batteries), noting the + and - configuration inside the battery compartment. The Baby unit operates cordlessly for up to 30 hours POWER light (A-2) flashes when battery power is low. If this happens install Note: To switch off the Baby unit completely push the POWER button (A-4) . Small Parent unit The small Parent unit uses a rechargeable battery pack. This is already installed, but first it must be charged for at least 14 hours as follows before using the unit outside the charging base: • Connect the AC power adapter (B-11) to an AC mains socket, and then connect power supply socket (B-10) of the charging base (B-6). • Place the small Parent unit inside the charging base. The red charging light (B-13) lights. The small Parent unit can be operated now but you should leave it in the charging base until the batteries are fully charged (at least 14 hours). When the batteries are fully charged, take the small Parent unit out of the charging base and use cordlessly for up to 12 hours. When the red POWER light (B-2) on the small Parent unit flashes, the battery power is low. Place the small Parent unit inside the charging base to recharge the batteries. Big Parent unit Connect the AC power adapter (C-9) to an AC mains socket, and then connect the cord to the DC power supply socket (C-8) of the big parent unit. If you want to use batteries, remove the battery compartment cover (C-6) using a screwdriver. Insert four 1.5V, AA batteries (not included; we recommend non-chargeable Philips Alkaline batteries), noting the + and - configuration inside the battery compartment. Put the cover back in place and tighten screw. The big Parent unit operates cordlessly for up to 30 hours on fresh batteries. The red POWER light (C-1) flashes when battery power is low. If this happens install new batteries. 5 14/10/2002, 11:29 HOW TO USE THE BABY MONITOR Monitoring baby’s sounds Both Parent units can be used at the same use the units to listen to your baby: • Position the Baby unit at least 1 metre baby’s sounds. • Set the channel switch to the same position • Push the POWER switch on the baby unit (A-4) to switch it on. • The green TRANSMIT light (A-3) lights when a sound is picked up. • Move away from the Baby unit with the Parent unit. • Switch on the big Parent unit using the Volume control/Off (C-4) and adjust the volume to the level you prefer. • Switch on the small Parent unit using the Volume control/Off (B-5) and adjust the volume to the level you prefer. The green SYSTEM CHECK lights (B-1, C-2) light continuously when the Parent units and the Baby unit are in touch with each other. 6 IFUSC369ENbk.p65 6 ADDITIONAL FEATURES Avoiding interference All units use anti-interference technology to reduce the chance interference from other signals. If interference does occur or if sound reception is poor, try switching all units to the other improve the sound quality. Note: Always make sure that the channel selection switches (A-6, B-set to the same position. Sound-level lights The big Parent unit has sound-level lights (C-5), which visually the volume control is turned down. The louder the sound received lights light. Checking that the units are in touch The green SYSTEM CHECK lights (B-1, C-2) of the Parent units light continuously to show that the Parent units and the Baby unit are in touch with each other. This light flashes if the Baby unit is out of range for more than 30 seconds or if the signal is blocked. When the units are no longer in touch, try one of the following: • Move the Parent unit closer to the Baby unit. (The maximum operating distance is 200m in conditions. Walls and floors can limit this distance.) • Switch all units to the other channel. • Check that the units are powered correctly (low batteries?). Switching on the audible warning If you w...
Dieses Handbuch ist für folgende Modelle:Trockner - SBC SC369 (3.38 mb)
Trockner - SBC SC369 (3.38 mb)