Stimmen - 2, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
Directives: -73/23 EEC of 19.2.73 (Low Voltage Directive) and subsequent modifications; -89/336 EEC of 3.5.89 (Electromagnetic Compatibility Directive) and subsequent modifications. 4 Description of the Appliance 1 Control panel 2 Water reservoir 3 Drum Light 4 Fluff filters 5 Rating Plate 6 Condenser unit 7 Adjustable feet 8 Drying rack 5 Installation It is dangerous to alter the specifications or attempt to modify this product in any way. Care must be taken to ensure that the appliance does not stand on the electrical supply cable. Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person. Technical Specifications DIMENSIONS Height Width Depth 85 cm (33.5”) 60 cm (23.6”) 58 cm (22.8”) POWER SUPPLY VOLTAGE TOTAL POWER ADSORBED 230-240 V/50 Hz 2350 W (13A) MAX LOAD CAPACITY Cotton, linen Synthetics 7 kg (15.4 lbs) 3 kg ( 6.6 lbs) DRUM VOLUME 108 l CONSUMPTIONS Cotton, linen (1000 rpm) Cotton, linen (1000 rpm) Synthetics (1200 rpm) 4.50 kWh (7 kg cupboard dry) 3.40 kWh (7 kg iron dry) 1.60 kWh (3 kg cupboard dry) 6 7 To keep vibration and noise to a minimum when the dryer is in use, it should be placed on a firm, level surface. Once in its permanent operating position, check that the dryer is absolutely level with the aid of a spirit level. If it is not, raise or lower the feet until it is. The feet must never be removed. Do not restrict the floor clearance through deeppile carpets, strips of wood or similar. This might cause heat build-up which would interfere with the operation of the appliance. Important The hot air emitted by the tumble dryer can reach temperatures of up to 60°C. The appliance must be sited in a well ventilated room but not be installed on floors which are not resistant to high temperatures. When operating the tumble dryer, the room temperature must not be lower than +5°C and higher than +35°C, as it may affect the performance of the appliance. Stacking kit (optional accessory) It should be possible to stack your new dryer on top of a front loading washing machine with cover’s depth between 48 and 60 cm. Read carefully the instructions supplied with the stacking kit. Please contact your local John Lewis branch for further advice. Door reversal To make it easier to load or unload the laundry the door can be reversed. This operation must be carried out by qualified personnel. Please contact The telephone number given under Repairs - After Sales Service (page 21). Unpacking Warning ! Slide out the polythene bag containing the polystyrene block before using the appliance. Pull off adhesive strips from inside machine on top of drum. Keep all packaging away from children. Should the appliance be moved, it must be transported vertically. Remove the rack The drying rack offers the possibility of drying washable woollen fabrics and sports shoes. The drying rack does not turn with the tumble dryer drum. This enables the drying of woollen garments or sports shoes. When wet, the wool must be moved as little as possible because it tends to become matted. Sports shoes could damage the drum due to their weight. 1. Lift the rack out of the polystyrene protection used for transport and remove it from the tumble dryer drum. 2. Remove the pieces of polystyrene from the drum one at a time. 3. Remove the elastic band from the rack and the rack container. Positioning It is recommended that, for your convenience, the machine is positioned close to your washing machine. The tumble dryer must be installed in a clean place, where dirt does not build up. Air must be able to circulate freely all around the appliance. It is important to ensure the air intake grills on the back of the dryer are not obstructed with any materials (e.g. paper, rags etc.). Obstructing the grills could be dangerous or at least seriously impair the efficiency of the tumble dryer. Electrical connection Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person. WARNING: THIS APPLIANCE MUST BE EARTHED. Should the appliance power supply cable need to be replaced, this must be carried out by a Service Force agent (see page 21). The manufacturer declines any liability should this safety measure not be observed. Before switching on, make sure the electricity supply voltage is the same as that indicated on the appliance’s rating plate. (See picture on page 5). The appliance is supplied with a 13amp plug fitted. In the event of having to change the fuse in the plug supplied, a 13amp ASTA approved BS 1363/A fuse must be used. Should the plug need to be replaced for any reason, proceed as described below. The wires in the mains lead are coloured in accordance with the following code: Green and Yellow - Earth Blue - Neutral Brown - Live If you fit your own plug, the colours of the wires in the mains lead of your appliance may not correspond with the markings identifying the terminals in your plug. Proceed as fol...