Stimmen - 3, Durchschnittliche Bewertung: 4 ( )

Hersteller: KitchenAid Dateigröße: 1.5 mb Dateiname: Use%20and%20Care%20Guide%20-%203387335.pdf Unterrichtssprache:

Warm air escapes from the dryer into the room. lengthen drying time. 3. Don't overdry. Use an automatic cycle to help prevent overdrying. Remove load when dryer stops. 9. Locate dryer in a warm area. Drying time is longer in unheated garages or utility rooms. 4. Dry only full loads. Drying 5. Separate light from heavyweight fabrics for faster, more even drying. small loads wastes energy. 10. Make sure the dryer is exhausted properly to the outside. Keep exhaust duct clean and check flapper to make sure it opens and closes freely. 6 Load Preparation For best results, the following steps should be taken to prepare your clothes for drying. • Empty all pockets. A small scrap of paper can cause a lot of lint. Turn pockets of heavy items inside out for even drying. • Remove heat-sensitive trim that can be damaged by drying. • Tie strings and sashes so they won't tangle. • Close zippers, snaps and hooks to avoid snagging other items. Remove any sharp or heavy objects that could damage the dryer drum. • Turn lint givers and takers and dark items inside out to help prevent lint pickup. • Put small items (baby socks, handkerchiefs) in a small mesh bag for easier removal. • Check garments to make sure all spots and stains were removed during the wash. If stains were not removed, do not tumble dry. Heat may permanently set the stain. Sorting Items properly sorted for washing are usually properly sorted for drying. For best results: • Separate heavy fabrics (denim and towels) from light fabrics (synthetics and permanent press). • Separate lint givers (towels and chenille) from lint takers (corduroy, synthetics and permanent press). When possible, turn lint givers inside out. • Separate dark from light colors, and colorfast from non-colorfast. Loading Load Sizes • A proper size washer load is generally a proper size dryer load. • For best drying results, do not dry more than two full-size sheets in one load, even if more than two sheets were in same washer load. Sheets need more space for proper air movement and maximum drying. Fill out the load with small items of the same type fabric. Fabric Softener Use only fabric softeners specifically labeled as not being harmful to the dryer. A fabric softener dispenser has been provided behind the control panel on the left side. • For best results, put a sheet of fabric softener on top of the load before starting the dryer. • Do not add the fabric softener sheet after the cycle has started. Instant heat may cause the fabric softener to spot fabrics. »If the fabric softener sheet becomes tangled or wrapped in one item during tumbling, a clear grease-like spot can result. If fabric softener has caused a stain, wet the stain and rub with liquid detergent or bar soap, then wash the item. Some fabric softeners may... 1. cause rust or residue deposits in the dryer and on fabrics; 2. clog the lint screen; 3. cause your dryer to overheat and/or fail to shut off. Static cling can be reduced by not overloading. Service or performance problems caused by the use of any product not manufactured by KitchenAid, Inc. are the responsibility of the manufacturer of that product. 7 Make Selections START BUTTON CYCLE SENTRY SELECTOR TEMPERATURE SELECTOR To reduce the risk of fire, electric shock or injury to persons, read the Important Safety Instructions on page 3 before operating your dryer. Select a Cycle To set the desired cycle, turn the Cycle Control Selector either left or right. Stop turning when the marker points to the cycle and setting of your choice. Refer to the Cycle Selection Chart on the next page, for recommended cycle and temperature settings. A description of each cycle can be found on pages 10-11. Select a Drying Temperature The Temperature Selector can be set anywhere on or between the four temperatures: EXTRA LOW, LOW, MEDIUM and HIGH. Refer to the Cycle Selection Chart on the next page, for the recommended temperature settings. Start the Dryer The dryer will start tumbling when the START button is pushed. To stop the dryer, open the door or turn the Cycle Control Selector to the OFF position. To start the dryer, close the door, select a cycle (if necessary) and push START. Setting the Cycle Sentry Your dryer will sound a signal to let you know when the cycle you have selected is finished. The signal can be adjusted or turned off by setting the Cycle Sentry Selector anywhere on or between HIGH and LOW or on OFF. The signal is helpful when drying permanent press, synthetics, and other items that should be taken out as soon as the dryer stops tumbling. 8 CLEAN SCREEN LIGHT CYCLE CONTROL SELECTOR Cycle Selection Chart Type of Load Suggested Cycle Suggested Temperature Cottons - Linens EXTRA HEAVY - Bedspreads, mattress pads, quilts HEAVYWEIGHT - Towels, jeans, corduroys, work clothes MEDIUMWEIGHT - Sheets, pillowcases, cotton underwear, diapers LIGHTWEIGHT -Batistes, organdies, lingerie AUTOMATIC REGULAR/HEAVY...

Herunterladen

Geben Sie zwei Ziffern: