Stimmen - 4, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
• At an angle, fit the footrest on the seat bottom, as shown. Seat Bottom Footrest IMPORTANT! Before assembly, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or broken. Contact Fisher-Price® for replacement parts and instructions if needed.Never substitute parts. Assembly • Slide a seat bottom tube through each set of plastic rings on the seat bottom. • Align the holes in the plastic rings and the seat bottom tubes. • Insert a #8 x 3/4" screw through each plastic ring and into the seat bottom tubes, as shown. • Tighten the screws with a Phillips screwdriver. Do not over-tighten. • Push the seat bottom tubes back and forth to be sure they are secured to the seat bottom. If the seat bottom tubes move, you have probably not fastened them properly. Remove the screws and check to be sure the screw holes in the seat bottom tubes and seat bottom plastic rings are aligned. Replace and tighten the screws. • Insert two #10 x 7/8" black screws through the footrest and into the seat bottom. • Tighten the screws with a Phillips screwdriver. Do not over-tighten. Footrest Insert Screws Here 4 Plastic Rings Plastic Rings Seat Bottom Tubes Plastic Rings Plastic Rings Seat Bottom Tubes 1 2 4 3 #8 x 3/4" Screw - 4 SHOWN ACTUAL SIZE #10 x 7/8" Black Screw - 2 SHOWN ACTUAL SIZE • Turn the seat bottom assembly upright. • Fit the seat back pins into the openings in the top side of the seat bottom assembly. Seat Bottom Assembly Seat Back Pin Seat Back Pin Opening Opening Assembly • Turn the seat assembly face down. • Insert the hinge rod through the hinge on the seat back and seat bottom, as shown. • Insert a #10 x 7/8" black screw into the hinge rod. • Tighten the screw with a Phillips screwdriver. Do not over-tighten. • Set the seat assembly aside for Assembly step 11. • Pull the frame leg out on each frame to open.Make sure it “clicks” into place. 5 Hinge Rod Long Tapered Leg Tube Hinge Frame Leg • Identify the back and front base.The back base has short leg tubes and the front base has long, tapered leg tubes.You will use the back base for the next assembly step. Front Base Back Base 5 6 8 7 #10 x 7/8" Black Screw SHOWN ACTUAL SIZE Short Leg Tube Assembly • While pressing the levers on the seat height adjusters, lift them to position 4 on the frame front legs, as shown. 6 Seat Height Adjusters Position 4 • Position a frame so that the decorated side is outward. • Insert the back leg of a frame into the back base. • Fit a screw retainer over the hole in the back base, as shown. • Insert a #10 x 7/8" black screw through the screw retainer and back base. • Tighten the screw with a Phillips screwdriver.Do not over-tighten. • Repeat this procedure to attach the other frame back leg to the other side of the back base. Screw Retainers Frame Back Legs Frame Decorated Side Back Base Hole Back Base Hole Press Lever 9 10 • Fit the seat assembly between the two frames. • Insert the seat bottom tubes into the sockets in each seat height adjuster. Seat Assembly Seat Bottom Tubes Sockets Sockets Hints: • Be sure the seat height adjusters are in the same position (position 4). • You may need to push the frames apart slightly to fit the seat bottom tubes into the seat height adjuster sockets. 11 #10 x 7/8" Black Screw - 2 SHOWN ACTUAL SIZE Screw Retainer - 2 Seat Height Adjuster Seat Height Adjuster Seat Bottom Tube Ends Back and Bottom View 7 Assembly • Push each seat height adjuster to be sure they are completely on the seat bottom tubes. • Insert a #8 x 3/4" screw through each seat height adjuster and the ends of the seat bottom tube. • Tighten the screws with a Phillips screwdriver. Do not over-tighten. Seat Bottom Tube Ends 14 Push Seat Height Adjuster Push Seat Height Adjuster #8 x 3/4" Screw - 2 SHOWN ACTUAL SIZE #8 x 3/4" Screw - 2 SHOWN ACTUAL SIZE 13 • From the back and bottom of the assembly, insert a #8 x 3/4" screw through both seat height adjusters and the ends of the seat bottom tube. • Tighten the screws with a Phillips screwdriver. Do not over-tighten. • Fit the frame front legs onto the front base. • Fit a screw retainer over a hole in the front leg. • Insert a #10 x 7/8" black screw through the screw retainer and front leg. • Tighten the screw with a Phillips screwdriver.Do not over-tighten. • Repeat this procedure to secure the other end of the front base with the remaining screw retainer and #10 x 7/8" black screw. Front Leg Hole Front Base Front Leg Hole Screw Retainers 12 #10 x 7/8" Black Screw - 2 SHOWN ACTUAL SIZE Screw Retainer - 2 Assembly 8 • Tip the assembly so that the back of seat is flat on the floor and the front and back bases are facing up. • Insert and “snap” the peg on a wheel into each of the four holes in the front and back bases. • Lift the assembly upright. • From the front of the assembly, place the pad onto the seat. • Lift the bottom of the pad. Insert the two elastic loops on the pad through the holes in the seat bottom. • F...
Dieses Handbuch ist für folgende Modelle:Stühle - DELUXE HEALTHY CARE B2105 (1.25 mb)