Stimmen - 2, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
In case of damage, DO NOT use. Contact Carrier/Invacare for further instructions. SAFETY SUMMARY The following recommendations are made for the safe and proper installation and use of the Ventilator Tray: GENERAL WARNINGS DO NOT install this equipment without first reading and understanding this instruction sheet. If you are unable to understand the Warnings, Cautions and Instructions, contact a healthcare professional, dealer or technical personnel if applicable, before attempting to install this equipment - otherwise, injury or damage may occur. D. Refer to INSTALLING THE VENTILATOR ARMS ONTO THE VENTILATOR TRAY/CHAIR FRAME in this Instruction Sheet. Ventilator Tray C. Refer to INSTALLING THE VENTILATOR TRAY ONTO THE CHAIR FRAME in this Instruction Sheet. INSTALLATION WARNINGS After ANY adjustments, repair or service and BEFORE use, make sure that all attaching hardware is tightened securely. INSTALLING THE VENTILATOR TRAY (FIGURE 1) NOTE: Refer to the following diagram for the proper location of the ventilator tray attachment points. 1. Attach the ventilator tray components in the following order: A. Install the ventilator tray hanger bracket onto the ventilator tray. B. Install the ventilator brace onto the chair frame. C. Install the ventilator tray onto the chair frame. D. Install the ventilator arms onto the ventilator tray/ chair frame. B. Refer to INSTALLING THE VENTILATOR BRACE ONTO THE CHAIR FRAME in this Instruction Sheet. Chair Frame A. Refer to INSTALLING THE VENTILATOR TRAY HANGER BRACKET ONTO THE VENTILATOR TRAY in this Instruction Sheet. FIGURE 1 - INSTALLING THE VENTILATOR TRAY/ATTACHMENT POINT LOCATIONS 1 Installing The Ventilator Tray Hanger Bracket Onto The Ventilator Tray (FIGURE 2) 1. Align the two (2) mounting holes in the ventilator tray hanger bracket with the two (2) mounting holes in the FRONT of the ventilator tray. 2. Secure the ventilator tray hanger bracket to the ventilator tray using two (2) 1/4 - 20 x 3/8-inch button head screws and self locking nuts. Securely tighten. Ventilator Tray Hanger Bracket 1/4 20 x 3/8-inch Self Locking Nuts Mounting Holes Button Head Screws FIGURE 2 - INSTALLING THE VENTILATOR TRAY HANGER BRACKET ONTO THE VENTILATOR TRAY Installing The Ventilator Brace Onto The Chair Frame (FIGURE 3) 1. Remove the self locking nut and plastic washer from the screw securing the roller to the chair frame. NOTE: Save the EXISTING self locking nut for reuse when installing the ventilator tray. Discard the plastic washer. 2. Align the mounting hole in the ventilator brace with the EXISTING screw securing the roller to the chair frame. 3. Secure the ventilator brace onto the EXISTING screw using the EXISTING self locking nut. Securely tighten. 4. Repeat STEPS 1 - 3 for the opposide side of the ventilator brace. EXISTING NOTE: The plastic washer Screw EXISTING Self Locking Chair Nut Frame Ventilator Brace Roller NOTE: Only one side of the ventilator brace attachment Mounting Hole is not shown. shown for clarity. FIGURE 3 - INSTALLING THE VENTILATOR BRACE ONTO THE CHAIR FRAME Installing The Ventilator Tray Onto The Chair Frame (FIGURE 4) 1. Position the two (2) tube clamps on the LOWER brace of the chair frame by firmly grasping each tube clamp, and bending it around the LOWER brace of the chair frame. NOTE: Be sure the open ends of the tube clamps are facing TOWARD the UPPER brace of the chair frame. 2. Position the ventilator tray between the MIDDLE brace and the LOWER brace of the chair frame, making sure the ventilator brace fits securely in the ventilator tray hanger bracket. 3. Align the two (2) MIDDLE mounting holes of the ventilator tray with the mounting holes in the two (2) tube clamps on the LOWER brace. 4. Secure ventilator tray to the two (2) tube clamps on the LOWER brace using two (2) 5/16 -24 x 1-1/2-inch hex head screws and self locking nuts. Hand tighten ONLY. 5. Position the clamp saddle under the ventilator tray hanger bracket AND the ventilator brace, making sure the two (2) mounting holes in the clamp saddle align with the two mounting holes in the ventilator hanger bracket. 6. Thread two (2) 1/4 -20 x 1-1/2-inch button head screws through one side of the ventilator hanger, the clamp saddle and the other side of the ventilator hanger, and secure using two (2) self locking nuts. Hand tighten ONLY. 2 Chair Frame Upper Brace Ventilator Tray Tube Clamp (STEP 1) Lower Brace Rear Middle Brace 5/16-24x1-1/2-inch Hex Head Screw (STEP 4) Self Locking Nut (STEP 6) Middle Mounting Hole (STEP 3) Mounting Hole (STEP 3) Tube Clamp (STEP 1) Self Locking Nut (STEP 4) Ventilator Tray Hanger Bracket (STEP 5) NOTE: The ventilator tray hanger bracket and the ventilator brace are shown unattached for clarity. Installing The Ventilator Arms Onto The Ventilator Tray/Chair Frame (FIGURE 5) 1. Position one (1) ventilator tray arm on the UPPER brace of the chair frame by firmly grasping the tube clamp on the top of the ventilator tray arm and bending it around the UPPER bra...