Stimmen - 2, Durchschnittliche Bewertung: 5
(
)
)
|
Anleitung Zusammenfassung
• LENGTH: 10 1/2” • HEIGHT: 9 1/2” • MAXIMUM PRESSURE: 100 psi • PRESSURE RANGE: 60 - 100 psi Tool Components And Specifications Cap exhaust O CO2 100 psi MAX. Warning label Latch button Magazine Fastener discharge area Work contact element (WCE) Trigger Quick clear nose Adjustable depth control (not visible) Nozzle shield 6 Operating Instructions MXN10400 Nails - Interchange Information MXN104 can use 3/8” to 1-1/4” 18 gauge brad nails designed for the following tools: • Bostitch® BT125SK-2 • Campbell Hausfeld® NB0030 • DeWalt® D51238K • Hitachi® NT32AE • Paslode® T125-F18 • Porter Cable® BN125 • Senco® Finish Pro™ 15 Staples - Interchange Information MXN104 can use 3/8” to 1-1/4” 18 gauge, 1/4” crown staples designed for the following tools: • Campbell Hausfeld® SN258K • Hitachi® N3804AB • Porter Cable® NS100, NS150 • Senco® SLS15, SLS18, SLS25XP Fasteners 1 1 MPA bar psi 1 1 7 . . . . 5 9 1 6 8 1 1 3 4 1 3 General Safety Information (Continued) Always assume the tool contains fasteners. Respect the tool as a working implement; no horseplay. Always keep others at a safe distance from the work area in case of accidental discharge of fasteners. Do not point the tool toward yourself or anyone whether it contains fasteners or not. Accidental triggering of the tool could result in death or serious personal injury. Do not drive a fastener on top of other fasteners. The fastener could glance and cause death or a serious puncture wound. Do not operate or allow anyone else to operate the tool if any warnings or warning labels are not legible. Warnings or warning labels are located on the tool magazine and body. Do not drop or throw the tool. Dropping or throwing the tool can result in damage that will make the tool unusable or unsafe. If the tool has been dropped or thrown, examine the tool closely for bent, cracked or broken parts and air leaks. STOP and repair before using or serious injury could occur. Clean and check all air supply hoses and fittings before connecting the tool to an air supply. Replace any damaged or worn hoses or fittings. Tool performance or durability may be reduced. Air compressors providing air to the tool should follow the requirements established by the American National Standards Institute Standard B19.3-1991; Safety Standard for Compressors for Process Industries. Contact your air compressor manufacturer for information. Operating The Tool RECOMMENDED HOOKUP The illustration below shows the recommended hookup for the tool. 1. The air compressor must be able to maintain a minimum of 60 psi when the tool is being used. An inadequate air supply can cause a loss of power and inconsistent driving. 2. Use 3/8” air hoses with a minimum working pressure of 150 psi. Use 1/2” air hoses for 50’ run or longer. For better performance, install a 3/8” quick plug (1/4” NPT threads) with an inside diameter of .315" (8mm) on the tool and a 3/8” quick coupler on the air hose. Caution indicates a potentially hazardous situation which, if not avoided, MAY result in minor or moderate injury. Do not make any modifications to the tool without first obtaining written approval from Campbell Hausfeld. Do not use the tool if any shields or guards are removed or altered. Do not use the tool as a hammer. Personal injury or tool damage may occur. Avoid long extended periods of work with the tool. Stop using the tool if you feel pain in hands or arms. Always check that the Work Contact Element (WCE) is operating properly. A fastener could accidentally be driven if the WCE is not working properly. Personal injury may occur (See "Checking the Work Contact Element" Section). Disconnect air supply and release tension from the pusher before attempting to clear jams because fasteners can be ejected from the front of the tool. Personal injury may occur. Notice indicates important information, that if not followed, MAY cause damage to equipment. Avoid using the tool when the magazine is empty. Accelerated wear on the tool may occur. NOTICE ! CAUTION Operating Instructions MXN10400 ! WARNING Recommended Hookup Quick Plug Quick Coupler Air Hose Quick Plug (Optional) Quick Coupler (Optional) Filter - Regulator 60 psi Min. 100 psi Max. 150 PSI WP 3/8” I.D. Operating The Tool (Continued) 3. For deeper penetration, turn the wheel (C) to left to the extent desired. 4. Make sure trigger and work contact element (WCE) move freely up and down without binding or sticking after each adjustment. ADJUSTING THE DIRECTION OF THE EXHAUST The MXN104 is equipped with an adjustable direction exhaust deflector. This is intended to allow the user to change the direction of the exhaust. Simply twist the deflector to any direction desired. CLEARING A JAM FROM THE TOOL 1. Disconnect the air supply from the tool. 2. Remove all fasteners from the magazine (see Loading/ Unloading). Failure to remove all fasteners will cause the fasteners to eject from the front of the tool. 3. Undo hook by pushing down on the button on the side of the magaz...