Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Read and follow all of these instructions carefully. FUNCTIONAL DESCRIPTION FOREWORD Porter-Cable Model FR350 is a heavy duty pneumatic framing nailer. It is designed to install .113" to .148" diameter, plastic collated round head, framing nails of various lengths (2" to 31/2"). Fastener collation angle is 22°. Use approved Porter-Cable fasteners only. POWER SOURCE This tool is designed to operate on clean, dry, compressed air at regulated pressures between 70 and 120 PSI (Pounds per Square Inch)(4.8 to 8.3 BAR). The preferred system would include a filter, a pressure regulator, and an automatic oiler located as close to the tool as possible, within 15 ft/4.6 m is ideal. All compressed air contains moisture and other contaminates that are detrimental to internal components of the tool. An air line filter will remove most of these contaminates and significantly prolong the life of the tool. If an in-line oiler is not available: place five or six drops of Porter-Cable Air Tool Oil into the tool’s air inlet at the beginning of each workday. The tool is equipped with a 1/4" male “quick connector”. A 3/8" male “quick connector” is available from Porter-Cable and may be used in situations where a 1/4" supply line is not available. A 3/8" supply line (and fittings) are required for maximum tool performance. The tool must always be connected to the air supply with a coupling such that all pressure is removed from the tool when the coupling is disconnected. All air line components (hoses, connectors, filters, regulators, etc.) must have a minimum working pressure rating of at least 150 PSI (10.3 BAR) or 150% of maximum system potential, whichever is greater. Do not connect tool to pressure which potentially exceeds 200 PSI (13.7 BAR). Only connect tool to air supply hose with a coupling that automatically removes all pressure from the tool when the coupling is disconnected. Disconnect tool from air supply before performing maintenance, clearing a jammed fastener, leaving work area, moving tool to another location, or handing the tool to another person. PREPARING THE TOOL 1. After reading and understanding this entire manual, connect tool to Never point tool at yourself or others. Always connect tool to air supply before loading fasteners (Fig. 18). Do not load fasteners with trigger or safety depressed. air supply (Fig. 18). 7 Fig. 19 << Fig. 20 Fig. 21 <<2 A << Fig. 18 Fig. 22 A B 1 Fig. 19 << Fig. 20 Fig. 21 <<2 A << Fig. 18 Fig. 22 A B 1 Only use approved Porter-Cable fasteners. Operator and others in work area MUST wear safety glasses with side shields. Always wear ANSI Z87.1 approved safety glasses, and ANSI S3.19 approved hearing protection when preparing or operating the tool. Never use a tool that is leaking air, has missing or damaged parts, or requires repair. 2. Pull follower all the way to the rear, until it latches (see Fig. 19). 3. Orient a strip of nails with points down (see Fig. 20), and drop into the magazine. Slide fasteners forward to the front of the magazine. The magazine will hold two full strips of fasteners. IMPORTANT: Fasteners must point in the same direction as they will be driven. 4. Pull back on the follower release lever (A) Fig. 21, and allow the follower to slide forward against nails. 5. Adjust directional exhaust deflector (A) Fig. 22, so that the exhaust air blast will be directed away from the operator: loosen deflector retaining screw (B) Fig. 22, rotate deflector to desired position for the current application and tighten retaining screw. 8 OPERATING INSTRUCTIONS USING THE TOOL WITH SELECTABLE TRIGGERING OPTIONS Complete all steps of PREPARING THE TOOL before using the tool. This tool is shipped from the factory with a selectable trigger set in the “SINGLE SEQUENTIAL ACTUATION” firing mode as described in number 1 below. The selectable trigger can be set for the “CONTACT ACTUATION” firing mode as described in number 2 below; 1. To use the tool in the SINGLE SEQUENTIAL ACTUATION MODE depress trigger lever pivot pin (A) Fig. 23, rotate arrow to position (B), and release. Note: Trigger lever pivot pin is spring loaded and held in position by locking tab (D) Fig. 23 to prevent movement during operation. To fire, grip tool firmly to maintain control, position nose of tool onto work surface, push tool firmly against work surface to depress safety, as shown at (S) Fig. 24, and then squeeze trigger to fire a fastener. Allow tool to recoil away from work surface as fastener is driven. This “single sequential actuation” method provides the most accurate fastener placement. -OR 2. To use the tool in the CONTACT ACTUATION MODE depress trigger lever pivot pin (A) Fig. 23, rotate arrow to position (C), and release. Note: Trigger lever pivot pin is spring loaded and held in position by locking tab (D) Fig. 23 to prevent movement during operation. To fire, grip tool firmly to maintain control, squeeze and hold trigger, push tool firmly against work surface to depress contact safety, as shown a...