Stimmen - 4, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Tags and physical segregation are recommended means of control. Danger indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury. REMINDER: Keep your dated proof of purchase for warranty purposes! Attach it to this manual or file it for safekeeping. Campbell Hausfeld Nailers meet or exceed For parts, product & service information IN726700AV 7/08Industries’ Standards as set forth by the visit American National Standard Institute/International Staple, Nail and Tool Association in ANSI/ISANTA SNT-101-2002. © 2008 Campbell Hausfeld/Scott Fetzer 2 General Safety Information (Continued) . Read and understand tool labels and manual. Failure to follow warnings, dangers, and cautions could result in DEATH or SERIOUS INJURY. . Do not use any type of reactive gases, including, but not limited to, oxygen and combustible gases, as a power source. Use filtered, lubricated, regulated compressed air only. Use of a reactive gas instead of compressed air may cause the nailer to explode which will cause death or serious personal injury. . Use only a pressureregulated compressed air source to limit the air pressure supplied to the tool. The regulated pressure must not exceed 110 psi. If the regulator fails, the pressure delivered to the tool must not exceed 200 psi. The nailer could explode which will cause death or serious personal injury. . Never use gasoline or other flammable liquids to clean the nailer. Never use the nailer in the presence of flammable liquids or gases. Vapors could ignite by a spark and cause an explosion which will result in death or serious personal injury. . Always remain in a firmly balanced position when using or handling the nailer. . Do not remove, tamper with, or otherwise cause the Work Contact Element (WCE) or trigger to become inoperable. Do not operate any tool which has been modified in a like fashion. Death or serious personal injury could result. . Do not touch the trigger unless driving nails. Never attach air line to nailer or carry nailer while touching the trigger. The tool could eject a fastener which will result in death or serious personal injury. Warning indicates a potentially hazardous situation which, if not avoided, COULD result in death or serious injury. . Always disconnect the tool from the power source when unattended, performing any maintenance or repair, clearing a jam, or moving the tool to a new location. Always reconnect the air line BEFORE loading any fasteners. Do not load the tool with fasteners when either the trigger is depressed or the Work Contact Element (WCE) is engaged. The nailer could eject a fastener causing death or serious personal injury. . Always fit tool with a fitting or hose coupling on or near the tool in such a manner that all compressed air in the tool is discharged at the time the fitting or hose coupling is disconnected. Do not use a check valve or any other fitting which allows air to remain in the nailer. Death or serious personal injury could occur. . Never place hands or any other body parts in the nail discharge area of the nailer. The nailer might eject a fastener and could result in death or serious personal injury. . Never carry the nailer by the air hose or pull the hose to move the nailer or a compressor. Keep hoses away from heat, oil and sharp edges. Replace any hose that is damaged, weak or worn. Personal injury or tool damage could occur. Operating Instructions Model JB006750 • REQUIRES: 0.7 SCFM with 10 nails per minute @ 90 psi • AIR INLET: 1/4” NPT • NAIL SIZE RANGE: 1” to 2-1/2” • MAGAZINE CAPACITY: 100 Nails per load, 16 gauge • WEIGHT: 4 lbs., 15 oz. • LENGTH: 12-1/2” • HEIGHT: 11-7/8” • MAXIMUM PRESSURE: 110 psi • PRESSURE RANGE: 70 - 110 psi Nailer Components And Specifications CAMPBELL PROFESSIONAL HAUSFELD Adjustable Exhaust Name, Spec and Warning Label (back-side and top) Magazine (open) Trigger Work Contact Element (WCE) No-Mar Tip Quick Clear Latch Depth Adjustment Wheel O CO2 Magazine Latch Recommended Hookup Quick Plug Quick Coupler Air Hose Quick Plug (Optional) Quick Coupler (Optional) Oiler Regulator Filter 3 General Safety Information (Continued) . Always assume the nailer contains nails. Respect the tool as a working implement; no horseplay. Always keep others at a safe distance from the work area in case of accidental discharge of nails. Do not point the tool toward yourself or anyone whether it contains fasteners or not. Accidental triggering of the nailer could result in death or serious personal injury. . Do not drive a nail on top of other nails. The nail could glance and cause death or a serious puncture wound. . Do not operate or allow anyone else to operate the nailer if any warnings or warning labels are not legible. Warnings or warning labels are located on the nailer magazine and body. . Do not drop or throw the tool. Dropping or throwing the tool can result in damage that will make the tool unusable or unsafe. If the too...