Stimmen - 3, Durchschnittliche Bewertung: 3.3
(
)
)
|
Anleitung Zusammenfassung
Check to be sure all supplied accessories are enclosed with the unit. In case of questions, damaged or missing parts, please call 1-800-543-6400 for customer assistance. CoNteNts u Angle Finish Nailer u 2-1/2 inch Angle Finish Nails u Operating Instructions u Warranty Card u Carry Bag AddItIoNAl IteMs Not INCluded u Compressor (must be able to maintain a minimum of 70 psi when the nailer is being used) u Air hose u Small tool for clearing jams u Threadlock glue u ANSI Z87 eye protection u Hearing protection and other personal protective equipment as required Assembly This tool comes fully assembled. The DANGER, WARNING, CAUTION, and NOTICE notifications and instructions in this manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. 7 Operating Instructions and Parts Manual Glossary Become familiar with these terms before operating the unit. ACTUATE (TOOL) — To cause movement to the tool’s component(s) intended to drive the fastener. ACTUATION SYSTEM — The use of a trigger, work contact element (WCE) and/ or other operating control, separately or in combination or sequence, to actuate the tool. AIR INLET — The opening in which the compressed air supply is connected, usually by means of a threaded fitting. FASTENERS — This tool uses 1 inch to 2-1/2 inch 15g 35° D-clipped head angle finish nails. MAGAzINE — The part of the nailer that holds the Fasteners. MAxIMUM AIR PRESSURE — The maximum allowable pressure of compressed air, as specified by the manufacture, for operating the tool. NO-MAR / STUD FINDER TIP — The no-mar / stud finder tip is designed to eliminate marks caused by the wire-formWork Contact Element (WCE). The no-mar tip may be removed and tethered to the tool if not required (See INSTALLING AND REMOVING NO-MAR / Stud finder TIP) or when a slightly deeper countersink is preferred. Simply slide the no-mar off the WCE and attach to the storage post on the magazine. The tip also functions as a convenient stud finder. To utilize the no-mar / stud finder tip, simply slide it over the tools WCE (see Figure 5). psi (POUNDS PER SqUARE INCH) —Measurement of the pressure exerted by the force of the air. The actual psi output is measured by a pressure gauge on the compressor. qUICK COUPLER — A quick coupler is designed to work in combination with a quick plug to quickly and easily join a pneumatic tool to an air hose (see Figure 3). qUICK PLUG — A quick plug is designed to work in combination with a quick coupler to quickly and easily join a pneumatic tool to an air hose (see Figure 4). REGULATOR — A device used to control air pressure to an air operated tool THREAD LOCK GLUE — A locking glue that is applied to the screw threads before installing. Prevents the screws from working loose during tool operation. CHN70600 Figure 3 - Quick Coupler Figure 4 - Quick Plug Figure 5 - No-mar / stud finder tip 8 Operating Instructions and Parts Manual CHN70600 Getting To Know Your Angle Finish Nailer Like A Pro Electronics ON / OFF Switch Conversion Switch Quick Clear Nose Stud Finder Operation Button Cover Nail Pusher Pusher Latch Button Low Nail Indicator Light Features ANtI-dry FIre This tool is equipped with an Anti-Dry Fire feature. This prevents the Work Contact Element (WCE) from being pushed in when only a few nails remain. Simply load new nail clip behind remaining nails to continue shooting. tetHered No-MAr / stud FINder tIP The tool is fitted with a no-mar tip which also acts as a convenient stud finder. To utilize the no-mar tip, simply slide it over the tools WCE. loW NAIl INdICAtor lIgHts The tool is equipped with lights on either side of the tool near the nose. When the nail count becomes low, the lights will turn yellow. When the nail count is nearly out, the Anti-Dry Fire feature will engage and the lights will turn red. (See Loading the Nailer section). NAIl PlACeMeNt lAser PoINter The tool is equipped with a laser mounted near the nose. This can be seen through the wide slots in the WCE and / or no- mar tip. The laser will indicate exact placement of the fastener. This is a Class IIIA Laser Product that emits laser radiation. Do not stare into beam or view directly with optical instruments. BuBBle level The tool is equipped with a bubble level located on the head cap. This will assist in aligning the tool for level driving of the fastener. The bubble level will assist in vertical and horizontal positioning of the tool. Bubble Level Adjustable Exhaust Deflecter Trigger Rubber Comfort Grip Swivel Plug Laser Electronics Audio Speaker Stud Finder Light ADC Thumbwheel Tethered No- mar / Stud finder Tip Work Contact Element (WCE) Stud Finder Light Low Nail Indicator Light Battery Cover/ Compartment No-mar tip Storage Post Pull-out Warning Decal Magazine Nail Loading Area Figure 6 - Components of the A...