Stimmen - 2, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
4. Push the magazine cover forward until latch button pops up. 5. Always unload all fasteners before removing tool from service. Unloading is the reverse of loading, except always disconnect the air supply before unloading. Latch Button Magazine Rail 60 psi Min. 100 psi Max. 150 psi or greater 3/8 inch I.D. Movement Adjust ing the Fastene r Penet ration The tool is equipped with an adjustable depth of drive feature. This allows the user to determine how deep a fastener will be driven into the work surface. 1. Adjust operating pressure so fasteners are driven consistently. Do not exceed 100 psi. 2. To drive the fastener shallower, turn the wheel (C) to right to the extent desired. 3. To sink a fastener deeper, turn the wheel (C) to left to the extent desired. 4. Make sure trigger and work contact element (WCE) move freely up and down without binding or sticking after each adjustment. Adjust ing The Direct ion Of The Exh aust The tool is equipped with an adjustable direction exhaust deflector. This is intended to allow the user to change the direction of the exhaust. Simply twist the deflector to any direction desired. 6 Operating Instructions Operating Inst ruct ions (Continued) Clearing A Jam From The Tool 1. Disconnect the air supply from the tool. 2. Remove all nails from the magazine (see "Loading/ Unloading The Nailer"). Failure to do so will cause the nails to eject from the front of the nailer. 3. Undo latch by pulling out and down. The wire latch will disengage from the hooks on the nose. 4. The door can now be rotated, exposing the jammed fastener. 5. Remove the jammed fastener, using pliers or a screwdriver if required. 6. Rotate door back into the closed position. 7. Extend the wire latch and place over the hooks on the nose. 8. Close the latch by pushing the latch up and in until the latch snaps into place. 9. Make sure the trigger and work contact element (WCE) move freely up and down without sticking or binding. Use r-Mainten ance Inst ruct ions Techn ical Service Please call our Tool Hotline at 1-800- 543-6400 with any questions regarding the operation or repair of this tool or for additional copies of this manual. Fastene r And Re placement Parts Use only genuine Campbell Hausfeld 18 gauge fasteners (or equivalent - see Fastener Interchange Information). Tool performance, safety and durability could be reduced if improper fasteners are used. When ordering replacement parts or fasteners, specify by part number. Tool Re pair Only qualified personnel should repair the tool and they should use genuine Campbell Hausfeld replacement parts and accessories, or parts and accessories which perform equivalently. Assem bly Procedu re For Seals When repairing a tool, the internal parts must be cleaned and lubricated. Parker O-lube or equivalent must be used on all o-rings. Each o-ring must be coated with O-lube before assembling. A small amount of oil must be used on all moving surfaces and pivots. After reassembling, a few drops of 30W non-detergent oil or equivalent, must be added through the air line before testing. Storage The stapler should be stored in a cool dry place. (C) Movement Rotate SN328K00 fasteners The following Campbell Hausfeld finishing fasteners are available at local retail stores If you need help locating any item, call customer service at 1-800-543-6400 Campbell Hausfeld fasteners meet or exceed ASTM Standard F1667 Model # length Wire Diameter Crown Size point finish Collation Staples per Stick Staples per box FN158K00 1/2 inch 18 Gauge 1/4 inch Chisel Galvanized/Vinyl Coated Adhesive 100 5000 FN168K00 5/8 inch 18 Gauge 1/4 inch Chisel Galvanized/Vinyl Coated Adhesive 100 5000 FN208K00 3/4 inch 18 Gauge 1/4 inch Chisel Galvanized/Vinyl Coated Adhesive 100 5000 FN258K00 1 inch 18 Gauge 1/4 inch Chisel Galvanized/Vinyl Coated Adhesive 100 5000 FN180615AV 1/2 inch 18 Gauge 1/4 inch Chisel Galvanized/Vinyl Coated Adhesive 100 1000 FN180620AV 3/4 inch 18 Gauge 1/4 inch Chisel Galvanized/Vinyl Coated Adhesive 100 1000 FN180625AV 1 inch 18 Gauge 1/4 inch Chisel Galvanized/Vinyl Coated Adhesive 100 1000 FN180630AV 1-1/4 inch 18 Gauge 1/4 inch Chisel Galvanized/Vinyl Coated Adhesive 100 1000 interchange information Staples used in the SN328K00 Finishing Stapler will also work in: Senco LN4450, SJS-LR, SKS L11-15, Hitachi N3804A, Duofast BN-1832S, KN-1848, Stan-Tech SDS 18-14, Atro Minor 90/30, 90/32, 90/40, and Porter Cable NS100 7 Operating Instructions Troubleshooting Chart Stop using stapler immediately if any of the following problems occur. Serious personal injury could occur. Any repairs or replacements must be done by a Qualified Service Person or Authorized Service Center. Symptom possible Cause(s) Corrective action Air leaking at trigger valve O-Rings in trigger valve housing are Replace o-rings and check operation of Work area damaged Contact Element (WCE) Air leaking between housing and nose 1 Loose screws in housing 2 Damaged O-Rings 3 Damage to bu...
Dieses Handbuch ist für folgende Modelle:Nailers - SN328K00 (3.07 mb)