Stimmen - 3, Durchschnittliche Bewertung: 4.7
(
)
)
|
Anleitung Zusammenfassung
Contact your air compressor manufacturer for information. ! NOTICE l Do not drive a nail on top of other nails. The nail could glance and cause death or a serious puncture wound. l Do not operate or allow anyone else to operate the nailer if any warnings or warning labels are not legible. Warnings or warning labels are located on the nailer magazine and body. l Never leave the nailer unattended or connected to an air compressor when not in use. Serious personal injury can occur if someone picks up and uses the nailer without knowing the correct way to operate the nailer. l Do not drop or throw the tool. Dropping or throwing the tool can result in damage that will make the tool unusable or unsafe. If the tool has been dropped or thrown, examine the tool closely for bent, cracked or broken parts and air leaks. STOP and repair before using or serious injury could occur. Caution indicates a potentially hazardous situation which, if not avoided, MAY result in minor or moderate injury. l Do not modify or alter the nailer or any nailer parts. Do not use the nailer if any shields or guards are removed or altered. Do not use the nailer as a hammer. Personal injury or tool damage may occur. l Protect your eyes and ears. Wear Z87 safety glasses, with side shields. Wear hearing protection. Employers and users are responsible for ensuring the user or anyone near the nailer wears this safety protection. Serious eye injury or permanent hearing loss could result. l Do not use a check valve or any other fitting which allows air to remain in the nailer. Death or serious personal injury could occur. l Never place hands or any other body parts in the nail discharge area of the nailer. The nailer might eject a fastener which could result in death or serious personal injury. l Never carry the nailer by the air hose or pull the hose to move the nailer or a compressor. Keep hoses away from heat, oil and sharp edges. Replace any hose that is damaged, weak or worn. Personal injury or tool damage could occur. l Always assume the nailer contains nails. Never use the nailer as a toy. Do not engage in horseplay. Always keep others at a safe distance from the work area in case of accidental discharge of nails. Never point the nailer at anyone. Accidental triggering of the nailer could result in death or serious personal injury. 2 ! WARNING Magazine Contact Trip Trigger Nailer Components And Specifications Operating Instructions Model NB0040 • REQUIRES: 1.3 SCFM with 10 nails per minute @ 90 psi • AIR INLET: 1/4” NPT • NAIL SIZE RANGE: 5/8” to 2” • MAGAZINE CAPACITY: 100 Nails per load, 18 gauge • WEIGHT: 2 lbs., 13 oz. • LENGTH: 91.2” • HEIGHT: 91.2” • MAXIMUM PRESSURE: 110 psi • PRESSURE RANGE: 70-110 psi Nail Discharge Area Nail Loading Area Adjustable Exhaust Work Contact Element (WCE) Warning Labels Connector Reload Indicator b. Depress work contact element by tapping the nose of tool against work surface in a bouncing motion. c. Each time the work contact element is depressed, a fastener will be driven. CHECKING THE WORK CONTACT ELEMENT (WCE) Check the operation of the Work Contact Element (WCE) trip mechanism before each use. The WCE must move freely without binding through its entire travel distance. The WCE spring must return the WCE to its fully extended position after being depressed. Do not operate the nailer if the WCE trip mechanism is not operating properly. Personal injury may occur. 1. Disconnect the air supply from the nailer. 2. Remove all nails from the magazine (see Loading/ Unloading The Nailer). 3. Make sure the trigger and work contact element (WCE) move freely up and down without sticking or binding. 4. Reconnect air supply to the nailer. 5. Depress the Work Contact Element (WCE) against the work surface without pulling the trigger. The nailer MUST NOT OPERATE. Do not use the tool if it operates without pulling the trigger. Personal injury may result. sure of 150 psi. Use 1/2” air hoses for 50’ run or longer. For better performance, install a 3/8” quick plug (1/4” NPT threads) with an inside diameter of .315" (8mm) on the nailer and a 3/8” quick coupler on the air hose. 4. Use a pressure regulator on the compressor, with an operating pressure of 0 -125 psi. A pressure regulator is required to control the operating pressure of the nailer between 70 and 110 psi. CONTACT TRIP SAFETY MECHANISM The NB0040 Brad Nailer is equipped with a contact trip safety mechanism. When both the trigger and the work contact element are depressed, a fastener will be driven. METHODS OF OPERATING A CONTACT TRIP NAILER: Do not touch the trigger unless driving nails. Never attach air line or carry nailer while touching the trigger. The tool could eject a fastener which will result in death or serious personal injury. SINGLE NAIL OPERATION This method is preferred for slower and more precise nail placement. a. Release trigger and place nose of tool against work surface. b. Depress the work contact element against wo...