Stimmen - 2, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
you need assistance in locating any accessory please contact: Black & Decker (U.S.) Inc, User Services Department, 10 North Park Drive, P.O. Box 85/, Hunt Valley.. MD 21030-0857. ' ■ • (CAUTION: The use of any other fastener or attachment might be hazardous.) To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment should be performed by Black and Decker Service Centers or other qualified service organizations, always using Black & Decker replacement parts Black & Decker (U S.) Inc. warrants this product for one year against any defects that are due to faulty material or workmanship Please return the complete unit, transportation prepaid, to the seller (if a participating retailer) for free replacement (proof of purchase may be required). The unit may also be returned to a Black & Decker Service Center or Authorized Service Station listed under “Tools Electric" in the Yellow Pages for free replacement or repair at our option This warranty does not apply to accessories This warranty gives you specific legal rights and you may have other rights which may vary from state to state, Should you have any questions, contact your nearest Black & Decker Center Manager Like most Black & Decker tools, this tool is listed by Underwriters Laboratories to ensure that it meets stringent safety requirements. .This symbol on the name plate means the product is listed by Underwriters’ Laboratories. Inc Important Commercial/Industry Use Warranty (One Year) # BUCKS DECKER Form No 313979 ©1987 Printed in USA (NOV87) Distributed by Black & Decker (U S ) Inc , 10 North Park Drive, P O Box 798, Hunt Valley, MD 21030-0798 /ri Instruction Manual Electric Stapler READ' THESE INSTRUCTIONS AND WARNINGS BEFORE OPERATING.THE UNIT. '' 120 VOLT 50/60 HZ ONLY. yjy WARNING. 1 o avoid serious eye Z._s A injury, eye protection equipment conforming to the requirements of ANSI* Z87 -1 and OSHA regulations MUST he worn by the tool operator and everyone in the vicinity of the tool Safety glasses conforming to those requirements have been supplied with Ihis tool Welcome to the World of Black & Decker Power Tools. Your new Electric Stapler Is the perfect toot to make repetitive, heavy duty stapling jobs easy and fast For personal safety and for proper operation of your Stapler, please take the time to carefully read all of the safety rules and instructions in this booklet. Don’t forget to send in the owner registration card. THANK YOU for buying BLACK and DECKER! # BUCK&DECKIR. Fastener Jamming When tested at the factory, this tool was as lam-proof as can bo, however, damage to parts or excessive accumulation of dirt can lead to improper operation of the toot tf a |am should occur, disconnect the lino cord, slide the magazine back and remove staples This quick-clear feature separates the front and rear nose sections so .the jammed fastener can be easily removed. If the toot is clean and jamming continues, contact your B&D representative for additional help. Plunger Assembly See Figures 4 and 5 . The Driver Blade and the Return Bumper are subject to normal wear and periodically must be serviced. To remove the Plunger Assembly, remove the Service Cap as shown in Figure 4 The Plunger Assembly may be slipped straight out To replace the Driver Blade: 1. Use a small drift punch to tap out the Roll Pin that retains the Blade to the Ptunger 2 Insert a new Blade and replace the Roll Pin. . CAUTION: Make sure- tin.; Moll Pin is below the outside diameter of tin* Plunger Any portion of the Pin protruding pasl lh* * Plunger diameter would cau.su damage In the electric coil To replace the Return hun»p*;i t Pull the oid Bumper out ol tin■ ¡'lunger Cap 2. Slightly moisten the fluted end of the new Bumper with water arid push in until it is fully seated in the- (:ap CAUTION: One or two drops nt water is sufficient to moisten DO NOT use any other type of lubricant WHEN REPLACING ANY PARI ON THIS TOOL—USE ONL Y IDENTICAL BLACK & DECKER REPLACEMENT PARTS PLUNGER ASSEMBLY' FIG. 4 i-RVIGE CAP 7 Operation cont’d OPERATING METHODS • Ilieft? nr* two standard methods of driving staples I vniGGEH OPFRAT ION (See Fig 2) 1 riggej operation method is the most commonly used. I his method assures aecur.'ite placement of the staple and the maximum riuve power, • Depress power switch. ■ • Position the front nose at the point whore the staple is to be driven (depiossing the triggering yoke). • Hold the tool firmly against the material to be fastened and pull the? liigger ' 2, YOKE OPERATION (TOUCH TRIP) (See Fig, 3) The Touch Trip method can be used when more speed and less accuracy and drive power are required, • Depress power switch • Pull the trigger • With the trigger depressed, strike the" nose against the work surface, thus depressing the safety yoke. WARNING: Do not operate the tool without fasteners. Maintenance & Repairs 'The following maintenance and repairs can be performed by the operator...