Stimmen - 3, Durchschnittliche Bewertung: 3.3 ( )

Hersteller: Grizzly Dateigröße: 695.18 kb Dateiname: Unterrichtssprache:

2. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of check- ing to see that keys and adjusting wrenches are removed from tool before operation. 3. KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents. 4. DO NOT USE IN DANGEROUS ENVIRONMENT. DO NOT use pneumatic tools in damp or wet locations, or where any flammable or noxious fumes may exist. Keep work area well lighted. 5. KEEP CHILDREN AND VISITORS AWAY. All children and visitors should be kept at a safe distance from work area. 6. MAKE WORKSHOP CHILD PROOF with padlocks, master switches, or by removing air hoses from tools. 7. DO NOT FORCE TOOL. It will do the job better and safer at the rate for which it was designed. 8. USE THE RIGHT TOOL. DO NOT force tool or attachment to do a job for which it was not designed. 9. DO NOT USE UNDER THE INFLUENCE OF DRUGS OR ALCOHOL. Safety Instructions For Pneumatic Tools 10. USE PROPER AIR HOSE for the 18. DISCONNECT TOOLS before sertool. Make sure your air hose is in vicing and changing accessories. good condition and is long enough to 19. USE THE RECOMMENDED reach your work without stretching. ACCESSORIES. Consult the 11. WEAR PROPER APPAREL. DO owner’s manual for recommended NOT wear loose clothing, gloves, accessories. The use of improper neckties, rings, bracelets, or other accessories may cause risk of jewelry which may get caught in injury. moving parts. Non-slip footwear is 20. CHECK DAMAGED PARTS. recommended. Wear a protective Before further use of the tool, a hair covering to contain long hair. guard or other part that is damaged 12. ALWAYS USE SAFETY GLASSES. should be carefully checked to Also use a face or dust mask if cut-determine that it will operate propting operation is dusty. Everyday erly and perform its intended funceyeglasses only have impact resis-tion. Check for alignment of moving tant lenses, they are NOT safety parts, binding of moving parts, glasses. breakage of parts, mounting, and 13. WEAR APPROVED HEARING any other conditions that may affect PROTECTION. its operation. A guard or other part that is damaged should be properly 14. SECURE WORK. Use clamps or a repaired or replaced. vise to hold work when practical. It is safer than using your hand and frees 21. NEVER LEAVE UNATTENDED both hands to operate tool. TOOL CONNECTED TO AIR. Disconnect the air hose and DO 15. DO NOT OVERREACH. Keep prop- NOT leave tool until it is relieved of er footing and balance at all times. any built up pressure. 16. MAINTAIN TOOLS WITH CARE. 22. NEVER ALLOW UNTRAINED Keep tools lubricated and clean for USERS TO USE THIS TOOL best and safest performance. Follow WHILE UNSUPERVISED. instructions for lubricating and changing accessories. 23. IF YOU ARE UNSURE OF THE INTENDED OPERATION, STOP 17. REDUCE THE RISK OF UNINTENUSING THE TOOL. Seek formal TIONAL FIRING. DO NOT carry tool training or research books or maga with hand on trigger and always diszines that specialize in pneumatic connect from air when not in use. tools. -2- H5626/H5627 Upholstery Stapler Basic Stapler Safety In addition to the rules stated in the previous section, and those in the warning boxes throughout this manual, please observe the following safety tips for your new stapler: 1. READ THIS ENTIRE MANUAL BEFORE OPERATING THE STAPLER. 2. ALWAYS DISCONNECT AIR FROM THE STAPLER whenever servicing or installing staples. During maintenance, a stapler connected to air may fire accidentally, causing serious personal injury. 3. DO NOT PLACE HANDS NEAR STAPLE POINT OF ENTRY. Staple can deflect and tear through the surface of the workpiece, puncturing your hand or fingers. 4. NEVER CONNECT THE STAPLER TO PRESSURIZED OXYGEN OR OTHER COMBUSTIBLE GASES as a power source. Only use filtered, lubricated, and regulated compressed air. 5. NEVER USE GASOLINE OR OTHER FLAMMABLE LIQUIDS TO CLEAN THE STAPLER. Vapors in the tool will ignite by a spark and cause the tool to explode. 6. DO NOT CARRY THE STAPLER BY ANY OTHER PART THAN THE HANDLE, and do not carry the stapler by the air hose. 7. DO NOT KEEP THE TRIGGER PULLED WHEN CARRYING OR HOLDING THE TOOL. 8. DO NOT USE A CHECK VALVE OR ANY OTHER FITTING that allows air to remain in the tool. Operating this stapler can propel objects into the air, causing immediate eye damage. To protect yourself, always wear American National Standards Institute (ANSI) approved safety glasses or goggles when operating this equipment. In addition, this stapler discharges at 85-90 decibels. To protect your hearing, always wear ANSI approved ear protection when operating this stapler. Never point this stapler at yourself or another person! Always pay attention to the direction this stapler is pointed. Use this tool with respect and caution to lessen the possibility of operator or bystander injury. Ignoring this warning may result in serious personal injury. H5626/H5627 Upholstery Stapler -3 -4- H5626/H5627 Upholstery Stapler INTRODUCTION Commentary Most importantly, we stand behind our tools. If you have any service q...

Herunterladen

Geben Sie zwei Ziffern: