Stimmen - 1, Durchschnittliche Bewertung: 3 ( )

Hersteller: Bostitch Dateigröße: 1.14 mb Dateiname: Unterrichtssprache:

. . . . . . . . . . . . .Replace trigger valve assembly O-ring or gasket is cut or cracked . . . . . . . . .Replace O-ring or gasket Bumpercracked/worn ...................Replacebumper Damagedgasketorseal .................Replacegasketorseal Cracked/worn head valve . . . . . . . . . . . . . . .Replace head valve Loose cap screws .......................Tighten and recheck Airsupplyrestriction ....................Checkairsupplyequipment Wornheadvalve .......................Replaceheadvalve Broken cylinder cap spring . . . . . . . . . . . . . . .Replace cylinder cap spring Headvalve stuck incap..................Disassemble/ Check /Lubricate Broken cylinder cap spring . . . . . . . . . . . . . . .Replace cap spring Rings/seals cut or cracked . . . . . . . . . . . . . . .Replace rings/seals Exhaustblocked ........................Checkbumper,headvalvespring Trigger assembly worn/leaks . . . . . . . . . . . . .Replace trigger assembly Dirt/tar build up on driver . . . . . . . . . . . . . . . .Disassemble nose/driver to clean Cylinder sleeve not seated correctly on bottom bumper .......................Disassemble to correct Airpressuretoolow .....................Checkairsupplyequipment Cloggedairfilter ........................Cleanorreplaceairfilter Wornbumper ...........................Replacebumper Tar/dirt in driver channel . . . . . . . . . . . . . . . . .Disassemble and clean nose and driver Air restriction/inadequate air flow through quick disconnect socket and plug . . . . . . . . .Replace quick disconnect fittings Wornpistonring ........................Replacering,checkdriver Damaged pusher spring..................Replace spring Lowairpressure ........................Checkairsupplysystemtotool Loose magazine nose screws . . . . . . . . . . . .Tighten all screws Fasteners too short for tool . . . . . . . . . . . . . . .Use only recommended fasteners Bentfasteners ..........................Discontinueusingthesefasteners Wrong size fasteners . . . . . . . . . . . . . . . . . . . .Use only recommended fasteners Leaking head cap gasket . . . . . . . . . . . . . . . . .Tighten screws/replace gasket Trigger valve O-ring cut/worn . . . . . . . . . . . . .Replace O-ring Broken/chipped driver . . . . . . . . . . . . . . . . . . .Replace driver (check piston ring) Dry/dirty magazine . . . . . . . . . . . . . . . . . . . . . .Clean/lubricate use BOSTITCH Air Tool Lubricant Wornmagazine .........................Replacemagazine Cloggedairfilter ........................Cleanorreplaceairfilter Driver channel worn .....................Replace nose/checkdoor Wrong size fasteners . . . . . . . . . . . . . . . . . . . .Use only recommended fasteners Bentfasteners ..........................Discontinueusingthesefasteners Loose magazine/nose screws . . . . . . . . . . . .Tighten all screws Broken/chippeddriver ...................Replacedriver -10- MAINTENANCE CHECKLIST Maintenance Benefit Procedure Service Interval Inspect trigger performance Ensure trigger system is in proper working order Refer to Tool Operation Check section in this manual Daily Drain condensation from air compressor tanks and air filters (if present) Prevents accumlation of moisture that can impede tool performace Open drain cock on tanks and air filters and drain all condensate Daily Clean magazine assembly Prevents accumlation of debris that could cause a jam Blow clean with compressed air Daily Clean nose assembly Prevents accumlation of debris that could cause a jam Blow clean with compressed air Daily Ensure all fasteners remain tight Prevent loose parts Tighten all fasteners with appropriately sized hex wrench Weekly Check/clean air inlet air filter Maintains proper air flow to engine for peak performance. Remove end cap and use compressed air blow gun to blow filter clean. Replace filter as required. 25,000 Fasteners, or monthly -if used in dusty location Replace no-mar tip Prevents marks in softwood applications Remove worn no-mar tip and replace with a new tip (a spare tip is located on the magazine) 25,000 Fasteners Replace swivel air fitting Maintains proper air flow to engine for peak performance Remove worn swivel air fitting and replace with new swivel fitting 50,000 Fasteners Replace piston/driver assembly Maintains consistent drive quality Refer to replacement part kit instructions 150,000 Fasteners Replace O-rings Maintains engine for peak performance Refer to replacement part kit instructions 250,000 Fasteners Replace bumper Maintains engine for peak performance Refer to replacement part kit instructions 250,000 Fasteners Replace headvalve Maintains engine for peak performance Refer to replacement part kit instructions 250,000 Fasteners Replace engine cylinder Maintains engine for peak performance Refer to replacement part kit instructions 500,000 Fasteners -11- OTHER BOSTITCH FLOORING PRODUCTS MIIIFS MIIIFN 16 GAUGE FLOORING NAILER FLOORING STAPLER 15.5 GAUGE MFN-201 20GAUGEMANUALFLOORINGNAILER PRO-3850 9.5MMX15MM(3/8”X50’) PREMIUMQUALITYPO...

Herunterladen

Geben Sie zwei Ziffern: