Stimmen - 5, Durchschnittliche Bewertung: 4 ( )

Hersteller: Husky Dateigröße: 1.59 mb Dateiname: Unterrichtssprache:

3. Make sure the trigger and work contact element (WCE) move freely up and down without sticking or binding. Movement 4. Reconnect air supply to the nailer. 5. Depress the Work Contact Element (WCE) against the work surface without pulling the trigger. The nailer MUST NOT OPERATE. Do not use the tool if it operates without pulling the trigger. Personal injury may result. 6. Remove the nailer from the work surface. The Work Contact Element (WCE) must return to its original down position. The nailer MUST NOT OPERATE. Do not use the tool if it operates while lifted from the work surface. Personal injury may result. 7. Pull the trigger and depress the work contact element (WCE) against the work surface. The nailer MUST NOT OPERATE. 21 8. Depress the Work Contact Element (WCE) against the work surface. Pull the trigger. The nailer MUST OPERATE. 12 4 Models HD219000, HD289000, & HD349000 Operational Modes (Continued) LOADING THE NAILER 1. Always connect the tool to the air supply before loading fasteners. 2. Pull nail pusher mechanism back until pusher engages with magazine latch. 3. Load strips of fasteners into the magazine slot. Make sure that the nails are placed into tool at the proper orientation. Nail pusher mechanism Latch 4. Squeeze the pusher and the latch together to unlatch pusher. Make sure the head of the last nail is under the head of the pusher. UNLOADING THE NAILER 1. Always unload all fasteners before removing tool from service. Unloading is the reverse of loading, except always disconnect the air hose before unloading. 2. Pull nail pusher mechanism back until pusher engages with magazine latch. Nail pusher mechanism Latch 3. Hold tool upright so nails will slide backwards toward magazine slot. 4. Squeeze the pusher and latch together to unlatch the pusher once all nails have been removed. ADJUSTING THE NAIL PENETRATION The HD219000, HD289000, and HD349000 nailers are equipped with an adjustable depth of drive feature. This allows the user to determine how deep a fastener will be driven into the work surface. 1. Adjust the operating pressure to a pressure which will consistently drive the fasteners. Do not exceed the maximum operating pressure of the nailer of 120 psi. 2. To adjust the depth-of-drive, loosen the 4mm bolt on the top of nose. To increase depth, push WCE in toward nose as much as desired. Retighten bolt. To decrease depth, pull WCE out as much as desired. Re-tighten bolt. 3. Make sure that the trigger and work contact element (WCE) move freely up and down without binding or sticking after each adjustment. ANTI-DRY FIRE The HD219000 is equipped with an Anti- Dry Fire feature. This prevents the WCE from being pushed in when only a few nails remain. Simply load new nail clip behind remaining nails to continue shooting. ADJUSTING THE DIRECTION OF THE EXHAUST The HD219000, HD289000, and HD349000 nailers are equipped with an adjustable direction exhaust deflector. This is intended to allow the user to change the direction of the exhaust. Using the 5mm wrench provided, loosen the deflector screw; then twist the deflector to any direction desired and re-tighten the screw. Rotate CLEARING A JAM FROM THE NAILER 1. Disconnect nailer from air supply. 2. Remove all nails from the magazine (see Loading/ Unloading). Failure to do so will cause the nails to eject from the front of the tool. 3. Insert a screwdriver into the nose of the tool. Push up on the driver blade to free the jammed nail. 4. Grab the jammed nail with pliers and remove. 5 Operating Instructions Technical Support Please call our Nailer Hotline at 1-800543- 6400 with any questions regarding the operation or repair of this nailer or for additional copies of this manual. Fastener And Replacement Parts See Fastener Interchange information. Use only genuine Husky replacement parts. Never substitute parts. Do not use modified parts or parts which will not give equivalent performance to the original equipment. Tool performance, safety and durability could be reduced. When ordering replacement parts, specify by part number. Nailer Repair Nailer repairs must be performed by qualified and experienced service people ONLY. Assembly Procedure For Seals When repairing a nailer, the internal parts must be cleaned and lubricated. Parker O-lube or equivalent must be used on all o-rings. Each o-ring must be coated with O-lube before assembling. A small amount of oil must be used on all moving surfaces and pivots. After reassembling, a few drops of 30W non- detergent oil, or equivalent, must be added through the air line before testing. Notes 6 Models HD219000, HD289000, & HD349000 Fasteners HD219000 Tool will also drive fasteners designed for: Campbell Hausfeld NS219000, Sears 18465, Porter Cable FR350, Hitachi NR83A, and Senco FramePro 702XP, 752XP, Ridgid R350RHA, and DeWalt D51844, D51845. HD289000 Tool will also drive fasteners designed for: Campbell Hausfeld NS289100, Sears 18420, Atro Helen 90CH, and Bostitch F28WW, N100S, N865, N805, N16. ...

Herunterladen

Geben Sie zwei Ziffern: