Stimmen - 2, Durchschnittliche Bewertung: 3 ( )

Hersteller: Porter-Cable Dateigröße: 7.39 mb Dateiname: Unterrichtssprache:

Carefully check for proper operation of trigger and safety mechanism. Do Not use the tool unless both the trigger and the safety mechanism are functional, or if the tool is leaking air or needs any other repair. The depth that a fastener is driven is controlled by the pressure of the air supply. The amount of pressure required will vary depending on the size of the fastener being used and the material being fastened. Experiment with the air pressure setting to determine the best pressure for the job at hand. Use only enough pressure to drive the fastener heads on top of the workpiece (not into the workpiece). Air pressure in excess of that required will cause premature wear and/or damage to the tool. 7 CLEARING A JAMMED FASTENER 1. CAUTION; Disconnect tool from air supply. 2. Open magazine and remove any remaining fasteners, 3. Open the quick release latch and hinge the fastener guide plate open (see Fig. 18). 4. Remove the jammed fastener (see Fig. 19). 5. . Close the fastener guide plate and secure with the quick release latch.. MAINTENANCE CLEAN AND INSPECT DAILY CAUTION: Disconnect tool from air supply before cleaning and inspection. Correct all problems before placing the tool back in use. Wipe tool clean and inspect for wear or damage. Use non-flammable cleaning solutions to wipe exterior of tool only if necessary. DO NOT SOAK tool with cleaning solutions. Such solutions can damage internal parts. Inspect trigger and safety mechanism to assure system is complete and functional: no loose or missing parts, no binding or sticking parts. Keep all screws tight. Loose screws can cause personal injury or damage tool. If tool is used without an in-line oiler: place 5 or 6 drops of Porter-Cable Air Tool Oil into the air inlet of the tool at the beginning of each workday. SERVICE AND REPAIRS All quality tools eventually require servicing or replacement of parts due to wear from normal use. Some user serviceable components are described in the TROUBLESHOOTING Section. Complete product Service is available from either an AUTHORIZED PORTER-CABLE SERVICE STATION or a PORTER-CABLE SERVICE CENTER. All repairs made by these agencies are fully guaranteed against defective material and workmanship. We cannot guarantee repairs made or attempted by anyone other than these agencies. Should you have any questions about your tool, feel free to write us at any time. In any communications, please give all information shown on the nameplate of your tool (model number, type, serial number, etc.). 8 TROUBLESHOOTING CAUTION: Disconnect tool from air supply before performing any Service Procedure. SYMPTOM PROBLEMS ' SOLUTIONS 1. Air leak near top of tool or in trigger area. Loose screws. Worn or damaged o-rings or seals, Tighten screws. Install ‘TOP’’ Maintenance Kit. 2. Tool does nothing or operates sluggishly. Inadequate air supply. Inadequate lubrication. Worn or damaged o-rings or seals. Verify adequate air supply. Put 5 or 6 drops of oil into air Inlet. Install ‘TOP” Maintenance Kit. 3. Air leak near bottom of tool. Loose screws. Worn or damaged o-rings or bumper. Tighten screws. Install “BOTTOM” Maintenance Kit. 4. Tool jams frequently. Incorrect fasteners. Verify approved fasteners of correct size. Damaged fasteners. Replace w/undamaged fasteners. Magazine or nose Tighten screws. screws loose. Magazine is dirty. Clean magazine. Driver is worn or damaged. Install “DRIVER” Maintenance Kit. 5. Other. Contact a Porter-Cable Service Facility. ACCESSORIES The testing of this too! has been accomplished with the following accessories. For safest operation, it is recommended that only these accessories be used with this product. WARNING: Since accessories other than those listed have not been tested with this product, use of such accessories could-be hazardous. CATALOG NO. DESCRIPTION LENGTH GAUGE QUAN/BC FN16075 16 Ga. Finish Nail, 3A" 3/4" 16 2500 FN16100 16 Ga. Finish Nail, 1" 1" 16 2500 FN16100-1 1000 Pk. of BN16100 16 1000 FN16125 16 Ga. Finish Nail, Va" VA" 16 2500 FN16125-1 1000 Pk. of BN 16125 16 1000 FN16150 16 Ga. Finish Nail, Va" 11/à" 16 2500 FN16150-1 1000 Pk. of BN16150 16 1000 FN16175 16 Ga. Finish Nail, 13A" 13/4“ 16 2500 FN16200 16 Ga. Finish Nail, 2'1 2“ 16 2500 FN16200-1 1000 Pk. of BN 16200 16 1000 60002 “TOP” Maintenance Kit 60006 “BOTTOM” Maintenance Kit 60012 “DRIVER” Maintenance Kit 884293 Oil (for Air Tools) 883763 Safety Glasses i PORTER-CABLE LIMITED ONE YEAR WARRANTY Porter-Cable warrants its nailing and stapling tools for a period of one year from the date of original purchase. We will repair or replace at our option, any part or parts of the product and accessories covered under this warranty which, after examination, proves to be defective in workmanship or material during the warranty' period. For repair or replacement return the complete tool or accessory, transportation prepaid, to your nearest Porter-Cable Service Cente...

Herunterladen

Geben Sie zwei Ziffern: