Stimmen - 1, Durchschnittliche Bewertung: 5 ( )

Hersteller: Black & Decker Dateigröße: 542.24 kb Dateiname: Unterrichtssprache:

Never load nails with the contact trip or trigger activated. 1. After reading and understanding this entire manual, connect tool to air supply. (Fig. 22) 2. Depress latch and slide magazine cover open. (Fig. 23) 3. Insert a strip of approved fasteners. (Fig. 24) Orient fasteners with points down in the magazine. 4. Push magazine cover closed. (Fig. 25) 5. Observe the low fastener indicator (A) Fig. 26 and reload as needed. 6. Adjust directional exhaust deflector (A) Fig. 27, so that the exhaust air or debris will be directed away from the operator. Grasp the deflector and rotate it to the desired position for the current application. Fig. 24 Fig. 25 Fig. 23 Fig. 22 7 492848-00,BDN200 NAILER 2/2/06 1:35 PM Page 8 Fig. 26A Fig. 27 A OPERATING INSTRUCTIONS USING THE TOOL Complete all steps of PREPARING THE TOOL before using the tool. This tool is shipped from the factory with a “single sequential actuation” trigger. To fire, grip the tool firmly to maintain control, position nose of tool onto work surface, push the tool firmly against work surface to depress safety (S) Fig. 28, and squeeze trigger to fire a nail. Allow tool to recoil away from work surface as nail is driven. This “single sequential actuation” method provides the most accurate fastener placement. Fig. 28 S Disconnect tool from air supply before performing maintenance, clearing a jammed fastener, leaving work area, moving tool to another location, or handing the tool to another person. Clean and inspect tool daily. Carefully check for proper operation of trigger and safety mechanism. Do Not use the tool unless both the trigger and the safety mechanism are functional, or if the tool is leaking air or needs any other repair. 8 492848-00,BDN200 NAILER 2/2/06 1:35 PM Page 9 The depth to which a nail is driven is controlled by the depth adjustment knob (A) Fig. 29. The depth of drive is factory adjusted to a nominal setting. Test fire a fastener and check depth. If a change is desired, rotate the adjustment knob (A) Fig. 29. The adjustment knob has detents every 1/4 turn. Rotate the knob (A) Fig. 29 clockwise to increase the depth of drive, rotate the knob counterclockwise to decrease the depth of drive. Test fire another fastener and check depth. Repeat as necessary to achieve desired results. The amount of air pressure required will vary depending on the size of the fastener and the material being fastened. Experiment with the air pressure setting to determine the lowest setting that will consistently perform the job at hand. Air pressure in excess of that required can cause premature wear and/or damage to the tool. A Fig. 29 CLEARING A JAMMED FASTENER Disconnect tool from air supply. 1. Open magazine and remove remaining fasteners. (Fig. 30 and Fig. 31) Remove fasteners from tool before opening the fastener guide plate. Fasteners are under pressure and may shoot out of magazine which could cause injury. 2. Remove the four screws from the fornt plate using the #3 and #4 hex head wrenches provided. (Fig. 32) 3. Remove the cover. 4. Move the spring loaded arm to the side and remove the steel plate to allow access to the jammed fastener. (Fig. 33) 5. Remove the jammed fastener using needle nose pliers if necessary. 6. Replace the steel plate, cover and 4 hex head screws. Fig. 31 Fig. 32 Fig. 33 Fig. 30 9 492848-00,BDN200 NAILER 2/2/06 1:35 PM Page 10 MAINTENANCE CLEAN AND INSPECT DAILY Disconnect tool from air supply before cleaning and inspection. Correct all problems before placing the tool back in use. Wipe tool clean and inspect for wear or damage. Use non-flammable cleaning solutions to wipe exterior of tool only if necessary. DO NOT SOAK tool with cleaning solutions. Such solutions can damage internal parts. Inspect trigger and safety mechanism to assure system is complete and functional: no loose or missing parts, no binding or sticking parts. Keep all screws tight. Loose screws can cause personal injury or damage tool. If tool is used without an in-line oiler: place five or six drops of air tool oil into the tool’s air inlet on a daily basis. IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (other than those listed in this manual) should be performed by authorized service centers or other qualified service organizations, always using identical replacement parts. TROUBLESHOOTING Disconnect tool from air supply before performing any Service Procedure. SYMPTOM PROBLEMS SOLUTIONS 1. Air leak near top of Loose screws. Tighten screws. tool or in trigger area. Worn or damaged B&D service for overhaul. o-rings or seals. 2. Tool does nothing or Inadequate air supply. Verify adequate air supply. operates sluggishly. Inadequate lubrication. Put 5 or 6 drops of oil into air inlet. Worn or damaged B&D service for overhaul. o-rings or seals. 3. Air leak near bottom Loose screws. Tighten screws. of tool. Worn or damaged B&D service for overhaul. o-rings or bumper. 4. Tool jams frequently. Incorrect fasteners. Verify ap...

Herunterladen

Geben Sie zwei Ziffern: