Stimmen - 2, Durchschnittliche Bewertung: 3 ( )

Hersteller: Black & Decker Dateigröße: 272.36 kb Dateiname: Unterrichtssprache:

4. Unplug charger, and remove the battery pack. Place the battery in the tool and be certain that it is inserted fully into the tool cavity until it “clicks” into place. NOTE: To remove the battery pack from the product, press down on the release button on the back of the battery (Figure 2) and pull out. Replace Pack The charger is designed to detect certain problems that can arise with battery packs which would be indicated by the red light flashing at a fast rate. If this occurs, re-insert battery pack. If problem persists, try a different battery pack to determine if the charger is OK. If the new pack charges correctly, then the original pack is defective and should be returned to a service center for recycling. If the new battery pack gives the same trouble indication as the original, have charger tested at an authorized service center. Wall Mounting (Figure 2A) A hole is provided in the center of the charger for mounting on a vertical surface. 2A 1 2 6 90514937 BDBN1202 1/18/07 9:14 AM Page 7 Leaving the Battery Pack in the Charger The charger and battery pack can be left connected with the red light glowing indefinitely. The charger will keep the battery pack fresh and fully charged. NOTE: A battery pack will slowly lose its charge when kept out of the charger. If the battery pack has not been kept on maintenance charge, it may need to be recharged before use. A battery pack may also slowly lose its charge if left in a charger that is not plugged into an appropriate AC source. Important Charging Notes 1. Longest life and best performance can be obtained if the battery pack is charged when the air temperature is between 65°F and 75°F (18°- 24°C). DO NOT charge the battery pack in an air temperature below +40°F(+4.5°C), or above +105°F (+40.5°C). This is important and will prevent serious damage to the battery pack. 2. The charger and battery pack may become warm to touch while charging. This is a normal condition, and does not indicate a problem. 3. If the battery pack does not charge properly — (1) Check power at receptacle by plugging in a lamp or other appliance. (2) Check to see if receptacle is connected to a light switch which turns power off when you turn out the lights. (3) Move charger and battery pack to a location where the surrounding air temperature is approximately 65°F - 75°F (18°- 24°C). (4) If charging problems persist, take or send the tool, battery pack and charger to your local service center. 4. The battery pack should be recharged when it does not produce sufficient power on jobs which were easily done previously. DO NOT CONTINUE use under these conditions. Follow the charging procedures. You may also charge a partially used pack whenever you desire with no adverse affect on the battery pack. 5. Black & Decker battery packs that are labeled “NiMH” should only be used with chargers labeled “NiMH“ or “NiCd/NiMH.” 6. Under certain conditions, with the charger plugged into the power supply, the exposed charging contacts inside the charger can be shorted by foreign material. Foreign materials of a conductive nature such as, but not limited to, steel wool, aluminum foil, or any buildup of metallic particles should be kept away from charger cavities. Always unplug the charger from the power supply when there is no battery pack in the cavity. Unplug charger before attempting to clean. 7. Do not immerse charger in water or any other liquid. SAVE THESE INSTRUCTIONS FOR FUTURE USE Features A. jam clearing latch B. contact trip C. no-mar pad D. low nail indicator windows E. magazine F. pusher release (other side) G. lock-off H. trigger I. LED Status Indicator NAIL SPECIFICATIONS Lengths 5/8'' - 2" (15 mm - 50 mm) F G I H A B C D E Diameters 18 gauge / calibre 18 7 90514937 BDBN1202 1/18/07 9:14 AM Page 8 3 Operating Instructions LED Status Indicator (Figure 3) The electronic indicator tracks the status and condition of the nailer. There are two basic indicators: • A flashing RED light indicates that the nailer has a jammed nail. • A permanent RED light indicates that the battery is low or out of power and needs to be charged. Using the Lock-Off (Figure 4) The nailer is equipped with a lock-off switch which prevents the tool from actuating. To engage, push the lock-off to the full rearward position as shown in figure 4. Loading the Tool (Figure 5) CAUTION: Keep tool pointed in a safe direction when loading nails. CAUTION: Never load nails with the contact trip or trigger activated. 5 CAUTION: Always engage lock off and remove battery pack before loading or unloading nails. To load fasteners: 1. Read all “Safety Warnings” before using tool. 2. Engage lock off. 3. Remove battery. 4. Depress pusher release and pull magazine back. 5. Insert fasteners into the side of the magazine. Be sure the fasteners ride on their tips in the nail channel as shown in figure 5A. 6. Push magazine closed until it locks in place. Actuating Tool WARNING: Always wear eye and ear protection when operating tool. To oper...

Herunterladen

Geben Sie zwei Ziffern: