Login:
Stimmen - 4, Durchschnittliche Bewertung: 3.8 ( )

Anleitung Makita, modell AN923

Hersteller: Makita
Dateigröße: 877.18 kb
Dateiname: 2a070a58-4fd3-4a49-9411-02329680990f.pdf
Unterrichtssprache:enesfr
Link zum kostenlosen Download Hinweise finden Sie am Ende der Seite



Anleitung Zusammenfassung


36. To maintain product SAFETY and RELIABILITY, maintenance and repairs should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. SAVE THESE INSTRUCTIONS WARNING: MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury. 3 SYMBOLS SYMBOLS 1 The followings show the symbols used for tool. ....................Read and understand tool labels and manual. ....................Operators and others in work area must wear safety glasses with side shields. ....................Keep fingers away from trigger when not driving fasteners to avoid accidental firing. INSTALLATION Selecting compressor 005686 Selecting air hose 004294 Use an air hose as large and as short as possible to assure continuous, efficient nailing operation. With an air pressure of 5.0 kgf/cm2G (70 PSIG), an air hose with an internal diameter of over 8.5 mm (5/16”) and a length of less than 20 m (6.6 ft.) is recommended when the interval between each nailing is 0.5 seconds. Air supply hoses shall have a minimum working pressure rating of 10.7 kgf/cm2G (150 PSIG) or 150 percent of the maximum pressure produced in the system whichever is higher. 8.5kgf/cm G(120PSIG)27.0kgf/cm G(100PSIG)26.0kgf/cm G(85PSIG)24.5kgf/cm G(65PSIG)2 3 (ft /min.) Compressor air output per minute CAUTION: • Low air output of the compressor, or a long or smaller diameter air hose in relation to the nailing frequency may cause a decrease in the driving capability of the tool. Lubrication 004295 4 3 2 1 To insure maximum performance, install an air set (oiler, regulator, air filter) as close as possible to the tool. Adjust the oiler so that one drop of oil will be provided for every 30 nails. When an air set is not used, oil the tool with pneumatic tool oil by placing 2 (two) or 3 (three) drops into the air fitting. This should be done before and after use. For proper lubrication, the tool must be fired a couple of times after pneumatic tool oil is introduced. 1 007005 1. Pneumatic tool oil 0 10 20 30 40 50 60 Nailing frequency (times/min) The air compressor must comply with the requirements of ANSI B19.3. Select a compressor that has ample pressure and air output to assure cost-efficient operation. The graph shows the relation between nailing frequency, applicable pressure and compressor air output. Thus, for example, if nailing takes place at a rate of approximately 40 times per minute at a compression of 6.0 kgf/cm2G (85 PSIG), a compressor with an air output over 3 ft3/minute is required. Pressure regulators must be used to limit air pressure to the rated pressure of the tool where air supply pressure exceeds the tool’s rated pressure. Failure to do so may result in serious injury to tool operator or persons in the vicinity. 4 FUNCTIONAL DESCRIPTION FUNCTIONAL DESCRIPTION CAUTION: • Always lock the trigger and disconnect the hose before adjusting or checking function on the tool. 007006 1 A B 1. Adjuster To adjust the depth of nailing, turn the adjuster. The depth of nailing is the deepest when the adjuster is turned fully in the A direction shown in the figure. It will become shallower as the adjuster is turned in the B direction. If nails cannot be driven deep enough even when the adjuster is turned fully in the A direction, increase the air pressure. If nails are driven too deep even when the adjuster is turned fully in the B direction, decrease the air pressure. Generally speaking, the tool service life will be longer when the tool is used with lower air pressure and the adjuster set to a lower depth of nail driving. Hook 007062 1. Hook 1 CAUTION: • Always lock the trigger and disconnect the hose from the tool. • Never hook the tool at high location or on potentially unstable surface. The hook is convenient for hanging the tool temporarily. To use the hook, simply lift up hook until it snaps into the open position. When not in use, always lower hook until it snaps into the closed position. ASSEMBLY CAUTION: • Always lock the trigger and disconnect the hose before carrying out any work on the tool. Loading nailer 007007 Select nails suitable for your work. Insert strip of nails into the magazine. Pull the pusher lever to the rear to engage the pusher to the last nail. 007008 1 1. Pusher Unloading nailer 007009 3 1 2 1. Pusher lever 2. Depress 3. Return Pull the pusher lever to the rear. Return the pusher lever back while keeping the pusher depressed to disengage it from the strip of nails. Depress the nail stopper and remove the strip of nails from the magazine. 5 007010 007010 Nail stopper 1 Connecting air hose 007011 1 2 1. Air socket 2. Air fitting Lock the trigger. Slip the air socket of the air hose onto the air fitting on the nailer. Be sure that the air socket locks firmly into position when installed onto the air fitting. A hose coupling must be installed on or near the tool in such a way that the pressure reservoir will discharge at the time the air supply coup...

Dieses Handbuch ist für folgende Modelle:
Nailers - AN943 (877.18 kb)

Bewertungen



Bewerten
Vorname:
Geben Sie zwei Ziffern:
capcha





Kategorien