Stimmen - 6, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
See Figure 8. 15 16 Figure 8 Figure 7 Figure 9 Figure 10 MANDATORY MAINTENANCE All maintenance and repairs should be performed by an authorized repair facility. Call 1-888-278-8092 to obtain a list of repair facilities in your area or to make arrangements to return the tool for service. ACTION REASON OPERATION TROUBLESHOOTING Most minor problems can be resolved quickly and easily using the troubleshooting table below. For problems that cannot be solved, contact Customer Service (toll free) at 1-888-278-8092. PROBLEM POSSIBLE CAUSE SOLUTION Always visually inspect round head nailer before every use. Check on the overall condition and for any loose screws. Tighten any screws that have come loose. See Figure 11. Visually inspect the work piece contact and trigger to ensure there is free movement. See Figure 12. When the tool is not going to be used for an extended period, wipe off all dust and debris that have collected on it. Tighten all loose screws. Lubricate the firing mechanism with pneumatic tool oil. See page 9 for Lubrication. Store the round head nailer in a safe location or in suitable carrying case. It is recommended that the air nailer be secured in a locked location to prevent unauthorized usage. Avoid exposure to direct sunlight and/or locations with high humidity and heat. Remove the round head nailer from use and schedule to have it repaired at an authorized repair facility if the work piece contact is binding or not moving freely. Do not attempt to repair the round head nailer. Failure to comply can result in malfunction of the tool and severe injury to the operator or any bystanders. Clean magazine and feeder mechanism. Prevents round head nailer from jamming. Use compressed air and clean daily. Inspect and ensure work piece contact operates properly. Ensures operator safety and keeps round head nailer working efficiently. Use compressed air and clean daily. Lubricate round head nailer after every use using pneumatic tool oil. Extends life of round head nailer. Apply 2 – 3 drops of pneumatic tool oil to round head nailer air inlet after every use. Nailer operates, but no nail is driven. Check for jammed nail. Ribbon spring weakened or damaged. Inspect nail feeder mechanism. Ensure correct nails are being used. Clear jammed nail. Replace ribbon spring. Clean and lubricate nail feeder. Use ONLY recommended nails. 17 18 Figure 11 Figure 12 PROBLEM POSSIBLE CAUSE SOLUTIO N PARTS DIAGRAM Weak drive. Slow to cycle between nailings. Ensure proper air pressure is being used. Inspect for worn driver blade. Inspect piston O-ring for wear or damage. Increase air pressure, Do not exceed 120 psig (8.3 bars, 8.5 kg/cm2) Contact Customer Service. Nails driven too deep. Check air pressure. Reduce air pressure. Round head nailer feeds intermittently or skips nails. Ensure correct nails are being used. Inspect nail feeder mechanism. Ribbon spring weakened or damaged. Piston O-ring damaged or worn Nail feeder worn or damaged. Use ONLY recommended nails. Clean and lubricate nail feeder. Replace ribbon spring. Use recommended pneumatic tool oil. Contact Customer Service. Replace nail feeder. Nails jam or driven nail is bent. Ensure correct nails are being used. Inspect for worn driver blade. Nail feeder worn or damaged. Use ONLY recommended nails. Contact Customer Service. Replace nail feeder. Drives nails properly during normal nailing operations, but fails to drive nails fully at faster operating speeds. Check inside diameter of air hose. Switch to air hose with larger inside diameter. 19 20 PARTS LIST ITEM NO. PART NO. DESCRIPTION 22 PARTS DIAGRAM 21 1 K0300-4011 Top Cap Set 2 A0000-0421 Nylon Screw M6*18 3 A0005-1071 Washer 4 A0304-0521 Exhaust Cover 5 A0000-0171 Screw M6*30 6 A0200-0811 O-Ring 11.8*1.5 7 A0005-0541 Washer 12.5*1.6T 8 A0203-0111 Muffler 9 K0300-4021 Top Cap & Screw Set 10 A0003-0331 Screw 11 A0301-1641 Cap, Top 12 A0317-0001 Wear Ring 13 A0100-1971 Spring 14 K0300-2741 Firing Valve Set 15 A0200-2612 O-Ring 39.4*3.2 16 A0200-3211 O-Ring 59.4*3.1 17 A0308-0491 Firing Valve 18 A0313-0281 Seal Firing Valve 19 A0005-0551 Washer Support 20 A0313-0121 Piston Retainer 21 K0600-3971 Piston Unit 22 A0200-1962 O-Ring 47.3*3.5 23 K0600-3961 Piston Set 24 A0305-0131 Collar ITEM NO. P A R T NO. DESCRIPTION ITEM NO. P A R T NO. DESCRIPTIO N 25 A0311-0351 Sleeve Hold Down 26 A0200-2002 O-Ring 85*3.5 27 A0800-0781 Spacer 28 A0303-0811 Cylinder 29 A0200-1852 O-Ring 57.5*3.3 30 A0200-3221 O-Ring 58*2.5 31 A0205-0411 Gasket 32 K0500-0901 Trigger Valve Set 33 A0204-1671 Grip 34 A0316-0341 Hook 35 A0706-1711 Support 36 A0000-0351 Screw M3*8 37 A0011-0171 Spring Pin 3*16 38 A0100-1051 Outlet Spring 39 A0000-1791 Nylon Screw M5*28 40 A0005-0531 Washer 14*1T 41 A0719-1121 Hook Fixer 42 A0005-0131 E-Ring 4 43 A0011-0091 Spring Pin 3*20 44 A0712-1181 Release Guide 45 A0313-0651 Main Body Bumper 46 A0011-0201 Sping Pin 3*30 47 A0009-0011 Steel Ball 48 A0100-1961 Spring 49 B0000-0351 Lock Pin Set 50 A0004-0021 Nylon Nut ...