Stimmen - 2, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
ASSEMBLY AND OPERATING INSTRUCTIONS NOTE: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram on page 14. Apply Pressure Here Power Cord (7) Safety (21) Nose (19) Trigger (13) Magazine (22) Lever (29) Fastener Window FIGURE 1 Warning: This Nailer / Stapler is not suited for nailing or stapling into concrete, masonry, bricks, or metal. Warning! Do not fire if Brad Nails or Staples are jammed in the Nose (19) section. Unplug the unit and follow the “Removing Jammed Staples or Brad Nails” on page 12. SKU 91494 For technical questions, please call 1-800-444-3353. Page 10 ASSEMBLY AND OPERATING INSTRUCTIONS (cont.) Warning! This Nailer has a Sequential Trip safety mechanism.With the nose of the Nailer contacting a surface, the unit will fire only once when the trigger is pulled. Testing the Sequential Trip Safety Mechanism 1. The Nailer should not fire if the Safety (21) is not depressed against the workpiece. 2. Make sure the tool is disconnected from the power supply. 3. Empty the Magazine (22) of nails. 4. Check that the Trigger (13) and the Safety (21) of the tool, move freely, without sticking. 5. Plug the tool into the power outlet. 6. Test the tool by depressing the Safety (21) of the tool against the workpiece without pulling the Trigger (13). The tool must not cycle (fire). If it cycles (fires), stop immediately and take the tool to an qualified service technician for repair. 7. Hold the tool away or off of the workpiece. The Safety (21) of the tool should return to its original position. Squeeze the Trigger (13). The tool should not cycle (fire). If it cycles (fires), stop immediately and take the tool to an authorized service technician. 8. Depress the Safety (21) of the tool against the workpiece and squeeze the Trigger (13). The tool must cycle (fire) once only. If it fails to cycle (fire) or fires more than once, take it to an authorized service technician. Warning! Disconnect the Nailer from the power outlet whenever loading it. Loading Brad Nails and Staples - See FIGURES 2 and 3 below. 1. Depress the Lever (29) and extend the Inner Magazine (24) all the way out . 2. When loading Brad Nails, make sure you insert the pins of the nails on the side of the Magazine (22) with the groove in it. The Brad Nails should fit into the groove. When loading staples, insert them crown up, into the Magazine (22). 3. Slide the extended Inner Magazine (24) back until the Lever (29) clicks into place. Do not force the Inner Magazine (24) or you may damage the tool. Inner Magazine (24) Lever (29) FIGURE 2 Insert staples here, crown up Lever (29) Depth Adjustment Knob FIGURE 3 REV 10/05 SKU 91494 For technical questions, please call 1-800-444-3353. Page 11 OPERATING INSTRUCTIONS When the unit is loaded with fasteners and you are ready to begin, plug the Nailer / Stapler Power Cord (7) into a power outlet. 1. Hold the tool with both hands, so that the Nose (19) is flat against the workpiece, making sure that the Safety (21) is also firmly FIGURE 4 against the workpiece. 2. Gently squeeze the Trigger (13) to fire the tool. 3. If you need a deeper driving depth, adjust the Depth Adjustment Knob. See FIGURE 3 on page 11 and FIGURE 4 to the right. Note: Practice depth adjustment on scrap material first. 4. If more depth is needed, and you are nailing or stapling into a hard surface, you may apply pressure on the top of the unit. See FIGURE 1 on page 10. On soft surfaces do not apply excessive pressure or the Brad Nail or Staple may penetrate the workpiece too deeply. Note: Each time you fire the Nailer / Staple Gun, the Safety (21) must be pressed firmly against the workpiece. Removing Jammed Staples or Brad Nails 1. First, unplug the Nailer / Stapler. If a nail is jammed in the discharge area, simply remove it with pliers. 2. If a nail is jammed in the Magazine (22), depress the Lever (29) and extend the Inner Magazine (24) all the way out. See FIGURES 2 and 3. Use a flat screwdriver and/or needle nose pliers to free the Brad Nail or Staple. INSPECTION, MAINTENANCE, AND CLEANING 1. WARNING! Make sure that the tool is unplugged from its electrical outlet before performing any inspection, maintenance, or cleaning procedures. 2. BEFORE EACH USE, inspect the general condition of the Nailer / Stapler. Check for loose screws, misalignment or binding of moving parts, cracked or broken parts, damaged electrical wiring, and any other condition that may affect its safe operation. If abnormal noise or vibration occurs, have the problem corrected before further use. Do not use damaged equipment. 3. Wipe tool clean with a lint free cloth and inspect it for damage. Do not use the tool if you find damage. Have it repaired by an authorized service technician. 4. Keep all screws tight. Loose screws may damage the tool and cause personal injury. 5. Make sure the Nose (19) is clear of all dirt or debris. SKU 91494 For technical questions, please call 1-800-444-3353. Page 12 PARTS LIST...