Stimmen - 4, Durchschnittliche Bewertung: 4.8
(
)
)
|
Anleitung Zusammenfassung
Testing the Double Trigger Safety Mechanism Warning: Even though the nailer should be empty during this procedure, ALWAYS point the nailer at a piece of scrap wood when testing. 1. Make sure the tool is disconnected from the power supply. 2. Completely empty the magazine of nails. 3. The Nailer should not fire if the second trigger Safety Trigger (123) Trigger (125) Figure 1 is not pulled. 4. Check that the Trigger (125) and the Safety Trigger (123) move freely, without sticking see Figure 1. 5. Connect the air supply to the tool at the Air Inlet (122) set at the recommended 60-100 PSI, and not to go over the maximum 100 PSI. 6. Hold the tool against the workpiece. Squeeze the Safety Trigger (123) and release it. The Safety Trigger should return to its original position. Squeeze the Trigger (125). The tool should not cycle (fire). If it cycles (fires), stop immediately and take the tool to an authorized service technician. 7. Squeeze the Safety Trigger (123) and then the Trigger (125). The tool must cycle (fire). If it fails to cycle (fire), take it to an authorized service technician. SKU 44923 For technical questions, please call 1-800-444-3353. Page 5 Loading Staples Loading Staples ALWAYS WEAR ANSI APPROVED IMPACT SAFETY GOGGLES WHEN RELOADING OR DOING ANY OTHER MAINTENANCE ON THIS TOOL. Other people in the work area must also wear ANSI approved impact safety goggles. Warning! Make sure the Nailer is not attached to the air hose whenever loading the tool. 1. The Nailer/Stapler should be in the same position as in Figure 2. 2. As in Figure 3, depress Magazine Lock (229) and slide Magazine Cover (227) open. 3. Slide the staples over the Magazine’s Core (216) (see Figure 4). 4. After the staples reach the nose of the tool, close the Magazine Cover (see Figure 5). Figure 5Figure 4 Magazine Cover (227)Core (216) Magazine Lock (229) Figure 3Figure 2 Magazine Cover (227) Loading Brad Nails ALWAYS WEAR ANSI APPROVED IMPACT SAFETY GOGGLES WHEN RELOADING OR DOING ANY OTHER MAINTENANCE ON THIS TOOL. Other people in the work area must also wear ANSI approved impact safety goggles. Warning! Make sure the Nailer is not attached to the air hose whenever loading the tool. 1. Follow Loading Staplessteps 1 and 2, above. 2. Insert the Brad Nails into the Magazine, letting the pointed end ride on the rail along the bottom of the Magazine (205) (see Figures 4 and 6). 3. After the Nails reach the nose of the tool, close the Magazine Cover (227) (see Figure 6, below). Figure 6 Magazine Cover (227) SKU 44923 For technical questions, please call 1-800-444-3353. Page 6 Operating the Nailer Operating the Nailer . Attach the Nailer to the air supply at the Air Inlet (122). Start your compressor and check the pressure making sure it is set at the recommended 60-100 PSI and not to go over the maximum 100 PSI. 2. To fire, place the nose of the Nailer on the workpiece. The Nailer should not fire if the Safety Trigger (123) is not depressed. Once depressed, gently and briefly squeeze the Trigger (125) once. Do not fire repeatedly. Nails could bounce off of one another, damaging the work piece or causing PERSONAL INJURY. Note: When using Brad Nails, the Driver Guide (206) might leave a slight mark on the surface of the workpiece which is larger than the nail brad. It occurs normally because the Driver Guide (206) tip is slightly wider to accomodate staples. To help avoid this, angle the tool slightly as shown in Figure 7. Figure 7 Anytime anymaintenance or repairs are done (including clearing jams), FIRST: 1. Disconnect the Nailer from the air hose. 2. Empty the Magazine (205) completely. 3. Attempt to fire the Nailer into a piece of scrap wood to ensure that it is disconnected and is incapable of firing any brads. 4. Always leave the Magazine Cover (227) open during maintenance. The Magazine is spring-loaded and may cause parts or a nail to fly out of the Nailer. Clearing Jams 1. Disconnect tool from air hose, empty the Magazine (205) of nails, release any built-up air pressure, and leave the magazine open, as explained above. 2. While doing this step and the next, hold the Nailer pointed away from you and any other people or fragile objects - see Figure 8. Loosen both Cover Hex Bolts (234) on Driver Guide Cover C (233) 3/4 of a turn each - see Figure 9. 3. Slide Driver Guide Cover C (233) toward the nose of the Nailer slightly until the holes (See Figure 9.) in Driver Guide Cover C (233) line up with the heads of both Cover Hex Bolts (234). 4. Carefully remove Driver Guide Cover C (233) and remove the jammed nail. Pliers may be necessary to remove a stuck nail. Figure 8 Figure 9 Cover Hex Bolt (234) Driver Guide Cover C (234) hole SKU 44923 For technical questions, please call 1-800-444-3353. Page 7 Clearing Jams (continued) Clearing Jams (continued) . Inspect the Driver (114) for bends or breakage - see Figure 10. If it is not fully retracted or damaged, do not use the tool until it is repaired by a qualified technician. 6. Lightly o...