Stimmen - 2, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
Hoses, couplers, oilers, regulators, and filters are all available at Harbor Freight Tools. TO ROOFING NAILER Note: To connect this tool, we recommend you use the included quick connector. If an oiler is not used, for smoother operation and to extend the life-span of the tool, put 3-5 drops of pneumatic tool oil in the attached quick connector (1) before each use. Testing the Full Sequential Safety Trip Mechanism Warning: Even though the nailer should be empty during this procedure, ALWAYS point the nailer at a piece of scrap wood when testing. 1. Make sure the tool is disconnected from the air supply. 2. Completely empty the Nail Cannister (82) of nails. 3. The Nailer should not fire if the nose is not depressed against the workpiece. 4. Make sure the Trigger (47) and nose move freely, without sticking - see the illustration on the following page. SKU 92359 For technical questions, please call 1-800-444-3353. PAGE 6 5. Connect the air supply to the tool at the Air Inlet (93). Set the regulator at the recommended 65 PSI to 120 PSI, and set not to go over the maximum 120 PSI. 6. Test the tool by depressing the nose against the workpiece without pulling the Trigger (47). The Tool must not cycle (fire). If it cycles (fires), stop immediately and have it repaired by a qualified service technician. 7. Hold the tool away or off of the workpiece. The nose of the tool should return to its original position. Squeeze the Trigger (47). The tool should not cycle (fire). If the tool fires, stop immediately and have it repaired by a qualified service technician. 8. Depress the nose against the workpiece and squeeze the Trigger (47). The tool must cycle (fire) only once. Release the Trigger and squeeze it again. The tool must not cycle (fire). With the Trigger held, carefully lift the nailer and press it against the workpiece again. The tool must not cycle (fire). If it fails to perform in the manner explained in bold, have it repaired by a qualified service technician. Loading Coil Nails ALWAYS WEAR ANSI APPROVED IMPACT SAFETY GOGGLES WHEN RELOADING OR DOING ANY OTHER MAINTENANCE ON THIS TOOL. Other people in the work area must also wear ANSI approved impact safety goggles. Warning! Make sure the Nailer is not attached to the air hose whenever loading the tool. NOSE TRIGGER (47) AIR INLET (93) SKU 92359 For technical questions, please call 1-800-444-3353. PAGE 7 1. To open the Cannister (82), press down on the Shaft (68) and swing the Latch (64) and Cannister Cover (89) open. 2. Check the Adjuster Plate (86) inside the Cannister (82). The Platform can be adjusted up and down to use various lengths of nails from 3/4” to 1-3/4”: A. Between 3/4” and 1” Long Nails (Use top setting). B. Between 1” and 1-1/4” Long Nails (Use middle setting). C. Between 1-1/4” and 1-3/4” Long Nails (Use bottom setting). CANNISTER COVER (89) CANNISTER (82) LATCH (64) SHAFT (68) FEED HOOK (50) LATCH (64) CANNISTER COVER (89) (TURN TO ADJUST) CANNISTER (82) NAILS ADJUSTER PLATE (86) REV 01/05 SKU 92359 For technical questions, please call 1-800-444-3353. PAGE 8 3. Place a coil of Nails (not included) around the Adjuster Plate (86) in the Nail Cannister (82). 4. Uncoil enough nails to reach the Feed Hook (50). Place the secondnail on the coil between the teeth of the Feed Pawl, making sure the nail head fits in the slot in the upper portion of the Feed Pawl. 5. Swing the Cannister Cover (89) closed. Then, close the Latch (64). Make sure the Latch closes securely. If it does not engage, the nail head is not in the slot in the upper portion of the Feed Hook (50). To AdjustThe Shingle Gauge: The Bracket (79) controls roof shingle spacing. To adjust the Bracket to work with a particular width of shingles, use the accessory Hex Wrench to loosen the Screw (80) on the Bracket. Slide the Bracket forward or backward to the desired spacing. Then, retighten the Screw. BOTTOM VIEW SCREW (80) BRACKET (79) SHINGLE SPACING Operating the Nailer 1. Attach the Nailer to the air supply at the Air Inlet (93). Start your compressor and check the pressure making sure it is set at the recommended 65-120 PSI and not to go over the maximum 120 PSI. 2. To fire, place the nose of the Nailer on the workpiece. The Nailer should not fire if the nose is not depressed. Once depressed, gently and briefly squeeze the SKU 92359 For technical questions, please call 1-800-444-3353. PAGE 9 Trigger (47) once and one nail will fire. To fire another nail, pull the nose of the nailer up off the workpiece, place the nose back down onto the next position on the workpiece and briefly squeeze the trigger. Repeat this procedure to continue firing nails. Do not fire nails on top of one another or into any foreign object. Nails could bounce off, damaging the workpiece or causing PERSONAL INJURY. Trigger (47) once and one nail will fire. To fire another nail, pull the nose of the nailer up off the workpiece, place the nose back down onto the next position on the workpiece and briefly squeeze the t...