Stimmen - , Durchschnittliche Bewertung:
(
)
)
Hersteller: Harbor Freight Tools
Dateigröße: 295.82 kb
Dateiname: 93197.pdf
Unterrichtssprache:
Das Dokument wird geladen, bitte warten
 |
Das Dokument wird geladen, bitte warten
Anleitung Zusammenfassung
Read warning labels if taking prescription medicine to determine if your judgement or reflexes are impaired while taking drugs. If there is any doubt, do not operate the tool. 19. Use proper size and type extension cord. If an extension cord is required for the air compressor, it must be of the proper size and type to supply the correct current to the tool without heating up. Otherwise, the extension cord could melt and catch fire, or cause electrical damage to the tool. Check your compressor’s manual for the appropriate size cord. Note: Performance of the compressor (if powered by line voltage) may vary depending on variations in local line voltage. Extension cord usage may also affect tool performance. 20. Maintenance. For your safety, maintenance should be performed regularly by a qualified technician. 21. Compressed air only. Never use combustible gases as a power source. SKU 93197 For technical questions, please call 1-800-444-3353. Page 3 Warning:The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. Warning:The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. -Lead from lead-based paints -Crystalline silica from bricks and cement or other masonry products -Arsenic and chromium from chemically treated lumber Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles. (California Health & Safety Code § 25249.5, et seq.) Unpacking When unpacking, check to make sure the parts listed on page 8 are included. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual as soon as possible Operation Floor Stapler 1/4”-18 NPT For best service you should incorporate an oiler, regulator, and inline filter, as shown in the diagram above. Hoses, couplers, oilers, regulators, and filters are all available at Harbor Freight Tools. 1. You will need to prepare a 1/4” air connector (sold separately) to connect to the air inlet on the Floor Stapler. First, wrap the 1/4” air connector (not included) with pipe thread seal tape before threading it into the Air Inlet (47). Connect the 3/8” ID Air Source Hose to the Air Inlet (47). Note: If you are not using an automatic oiler system, before operation, add a few drops of Pneumatic Tool Oil to the airline connection. Add a few drops more after each hour of continual use. 2. Set the air pressure on your compressor to between 70-90 PSI. Do not exceed the maximum air pressure of 100 PSI. 3. Check the air connection for leaks. Disconnect from the air source. SKU 93197 For technical questions, please call 1-800-444-3353. Page 4 Operation (continued) Assembly - Attaching the Arm (48) is the only assembly required. See FIGURE 1 and the Assembly Drawing on page 8. The two Clamp Screws (44) fit in the recessed gaps on the lower part of the Arm (48). As shown below, hold the Clamp Screws (44) in place around the Body (18) and add a Washer (45) and a Nut (46) to the threaded ends of the Clamp Screws (44). Tighten them securely. FIGURE 1 Hammer Face (10) (Pounding on this with the Hammer (49) shoots out a staple. Air Inlet (47) Magazine (30a) Arm (48) Sleeve (36a) Shoe (28) Staples exit the Stapler from the bottom of the Shoe (28). Loading the Stapler Recessed Gap Clamp Screws (44) Warning! Disconnect the Stapler from the air compressor whenever loading or servicing. After disconnecting the Stapler from the air compressor, there could still be enough air pressure to fire the Stapler. After the air compressor hose is disconnected, always fire the Stapler repeatedly to make sure all of the air is expended. See page 6 under “Using the Stapler” for firing instructions. 1. Grip the Sleeve (36a) and pull out the Magazine Cover (33a). Insert the staples inside the Magazine (30a). Note: Only use the size staples listed on the Specifications Chart on page 2. 2. Use caution, the Magazine Cover (33a) will try to snap closed with force when the Pin (38) is pressed. While holding the Sleeve (36a) firmly, use a small screwdriver to press in the Locking Pin (38) along the edge of the Magazine Cover. See FIGURE 2. Sleeve (36a) FIGURE 2 Magazine (30a) Air Inlet (47) Hammer Face (10) Shoe (28) Magazine Cover (33a) Locking Pin (38) SKU 93197 For technical questions, please call 1-800-444-3353. Page 5 Operation (continued) Using the F...