Stimmen - 4, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
2. USE ONLY CLEAN, DRY, REGULATED, COMPRESSED AIR AT BETWEEN 60 TO 115 PSI. Never use oxygen, carbon dioxide, combustible gases, or any other bottled gas as a power source for this tool. 3. NOTE: An air compressor is not provided. You will need an air compressor with a minimum rating of 4 to 6 CFM delivery at 90 PSI. 4. WHEN CONNECTING TO THE AIR SUPPLY: Prior to each use, if an automatic oiler is not used, add two drops of Air Tool Oil (part #95) into the Air Plug (part #33) of the Air Stapler. Attach the air compressor hose to the Air Plug. Turn on the air compressor, and set the regulator to the recommended 60 to 115 PSI for this tool. (See Figure A.) TO AIR COMPRESSOR TO AIR STAPLER PSI AIR REGULATOR ADJUST FROM 60 PSI TO 115 PSI FIGURE A SKU 54425 PAGE 4 5. ALWAYS DISCONNECT THE AIR SUPPLY HOSE FROM THE AIR STAPLER BEFORE LOADING THE STAPLES TO PREVENT A STAPLE FROM BEING ACCIDENTALLY FIRED DURING CONNECTION. The Air Stapler’s driving mechanism may cycle when the tool is connected to the air supply. When not in use, disconnect from air supply and remove all Stapes from the Moving Rail (part #76) of the Air Stapler. 6. DO NOT LOAD STAPLES WITH THE TRIGGER (part #31) OR SAFETY ELEMENT (part #55) DEPRESSED. Doing so may cause accidental firing of a Staple. 7. ALWAYS KEEP YOUR FINGER OFF THE TRIGGER (part #31) WHEN NOT DRIVING STAPLES. Never carry the Air Stapler with your finger on the Trigger, as the tool will fire a Staple if the Safety Element (part #55) is bumped while the Trigger is depressed. 8. ALWAYS ASSUME THE AIR STAPLER IS LOADED. Keep the tool pointed away from yourself and others at all times. 9. NEVER ATTEMPT TO DRIVE A STAPLE INTO MATERIAL THAT IS TOO HARD, AT TOO STEEP AN ANGLE, OR NEAR THE EDGE OF THE WORKPIECE. The Stapler may ricochet, causing personal injury to you or others nearby. 10. GRIP THE AIR STAPLER FIRMLY WITH BOTH HANDS TO MAINTAIN CONTROL, WHILE ALLOWING THE TOOL TO SLIGHTLY RECOIL AWAY FROM THE WORKPIECE AS A STAPLE IS DRIVEN. 11. MAKE SURE ALL ADJUSTING WRENCHES ARE REMOVED FROM THE AIR STAPLER BEFORE USING. 12. MAINTAIN A SAFE WORKING ENVIRONMENT. Keep the work area well lit. Make sure there is adequate surrounding workspace. Always keep the work area free of obstructions, grease, oil, trash, and other debris. Do not use the Air Stapler in areas near flammable chemicals, dusts, and vapors. 13. ALWAYS DISCONNECT THE AIR STAPLER FROM ITS AIR SUPPLY before performing any maintenance or cleaning of the tool, leaving the work area, moving the tool to another location, or handing the tool to another person. UNPACKING When unpacking, check to make sure all the parts shown on the Parts List on page 9 are included. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. SKU 54425 PAGE 5 ASSEMBLY INSTRUCTIONS NOTE: For additional references to the parts listed on the following pages, refer to the Assembly Diagram on page 10. To Attach A Quick Connector To The Air Stapler: 1. The Air Stapler requires the attachment of a 1/4”-18 NPT Quick Connector (not included) to the Air Plug (part #33) of the Air Stapler. To do so, wrap the threaded portion of the Quick Connector with about 3” of pipe thread seal tape (not included). Then, wrench tighten the Quick Connector into the Air Plug (See Figure B.) AIR PLUG (#33) QUICK CONNECTOR (NOT INCLUDED) WRAP THREADED PORTION WITH 3” PIPE THREAD SEAL (NOT INCLUDED) FIGURE B SAFETY ELEMENT (#55) TRIGGER (#31) NOSE OPERATING INSTRUCTIONS To Prepare The Air Stapler For Use: 1. CAUTION: Make sure to keep the Air Stapler pointed away from you and others at all times. Always disconnect the Air Stapler to its air supply before loading nails. Do not load nails with the Trigger (part #31) or Safety Element (part #55) depressed. (See Figure C, next page.) 2. Lift the Magazine Latch (part #39) up, and pull the Moving Rail (part #76) all the way to the rear until it latches. (See Figure C.) 3. Orient a strip of Staples with the points down, and drop the strip of Staples into the Moving Rail (part #76). (See Figure C.) SKU 54425 PAGE 6 MOVING RAIL (#76) MAGAZINE LATCH (#39) AIR HOSE (NOT INCLUDED) TRIGGER (#31) NOSE MOVING RAIL (#76) MAGAZINE LATCH (#39) AIR HOSE (NOT INCLUDED) TRIGGER (#31) NOSE 4. Slide the strip of Staples forward in the Moving Rail (part #76). NOTE: The Moving Rail will hold up to 110, 18 gauge, Staples. (See Figure C.) 5. Push the Moving Rail (part #76) forward, and allow the Magazine Latch (part #39) to lock the Moving Rail in place. (See Figure C.) SAFETY ELEMENT (#55) FIGURE C To Use The Air Stapler: 1. The Air Stapler can be used in two different ways. 2. The first way to use the Air Stapler is to place the Safety Element (part #55) on the working surface. Lightly push down on the Air Stapler until the Safety Element is depressed. Then, depress the Trigger (part #31) to drive a Staple. This “trigger fire” method provides the most accurate Staple placement...