Stimmen - 5, Durchschnittliche Bewertung: 3.6
(
)
)
|
Anleitung Zusammenfassung
The Tool should not fire if the Safety Nosepiece is not pressed against the workpiece. Full Sequential Safety Trip Mechanism Testing Procedure TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Empty the tool before this procedure. Point the tool at a piece of scrap wood when testing. 1. Disconnect the tool from the air supply. 2. Empty the Nail Canister (82) of fasteners. 3. Check that the Trigger (47) and the Safety Nosepiece move freely, without sticking. 4. Connect the air supply to the tool and set within the Operating Air Pressure indicated on the Specification chart. 5. Test the tool by pressing the Safety Nosepiece against the workpiece without pulling the Trigger. The Tool must not cycle (fire). If it cycles (fires), stop immediately and have it repaired by a qualified service technician. 6. Hold the tool away or off of the workpiece. The Safety Nosepiece should return to its original position. Squeeze the Trigger. The tool must not cycle (fire). If the tool fires, stop immediately and have it repaired by a qualified service technician. 7. Press the Safety Nosepiece against the workpiece and squeeze the Trigger. The tool must cycle (fire) only once. Release the Trigger and squeeze it again. The tool must not cycle (fire). With the Trigger held, carefully lift the tool and press it against the workpiece again. The tool must not cycle (fire). If it fails to perform in the manner explained in bold, have it repaired by a qualified service technician. Loading the Tool TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION, BEFORE LOADING: • Wear ANSI-approved safety goggles with side shields. Other people in the work area must also wear ANSI-approved safety goggles with side shields. • Release the trigger. • Detach the air supply. • Attempt to fire the Tool into a piece of scrap wood to ensure that it is disconnected and is incapable of firing any fasteners. 1. To open the Canister (82), push down on the Latch (68) and swing the catch (64) and the Canister Cover (89) open. See photos above right. 2. Check the Adjuster Plate (86) inside the Canister (82). The Platform can be adjusted up and down to use various lengths of nails from 3/4” to 1-3/4”: A. Between 3/4” and 1” Long Nails (Use top setting). B. Between 1” and 1-1/4” Long Nails (Use middle setting). C. Between 1-1/4” and 1-3/4” Long Nails (Use bottom setting). 3. Turn the Adjuster (88) clockwise to raise the Turntable (86) until its edge aligns with the embossed nail size markings on the inside wall of the Cannister. 4. Place a coil of Nails around the Adjuster Plate (86) in the Nail Canister (82). See photo, above. 5. Swing the Canister Cover (89) closed. Then, close the Catch Latch Latch (68) Canister Cover (89) Catch (64) Canister (82) Canister Cover (89) Nails Feed Hook (50) Adjuster Plate (86) Canister (82) (64). Make sure the Latch closes securely. If it does not engage, the nail head is not in the slot in the upper portion of the Feed Hook (50). 6. To adjust the Shingle Gauge: The Bracket (79) controls roof shingle spacing. To adjust the Bracket to work with a particular width of shingles, use the accessory Hex Wrench to loosen the Screw (80) on the Bracket. Slide the Bracket to the desired spacing. Then, retighten the Screw. See graphic, below. General Operating Instructions 1. Before each use, test the Tool as directed in the prior section. 2. If an automatic oiler is not used, add a few drops of Pneumatic Tool Oil into the tool’s airline connection before use. Add a few drops more after each hour of continual use. 3. Attach the Nailer to the air supply at the Air Inlet (93). Start your compressor and check the pressure making sure it is set at the recommended 65-90 PSI and do not exceed 90 PSI. 4. To fire, place the nose of the Nailer on the workpiece and push down until it stops. Pull the Trigger to fire one nail. Note: The Nailer should not fire if the Nose is not fully depressed. To fire another nail, lift the Nose of the Nailer off the workpiece, which will feed another nail into the firing chamber. Repeat previous step to fire. Avoid forcing the nose in an angle. Do not fire nails on top of each another or into any hard object. Nails could bounce off, damaging the workpiece or causing PERSONAL INJURY. See graphic, below. 5. Do not press the Nose of the Roofing Nailer against the work surface with excess force. Allow the tool to do the work. Always allow the tool to recoil off the workpiece. 6. Caution: While working on roofs, tar and dirt may build up on the Nose of the Roofing Nailer. This can prevent normal operation. Remove buildup with a nonflammable solvent. NEVER use gasoline or other flammable solvents. Do not immerse Roofing Nailer in an approved solvent beyond the height of the nail heads, to avoid getting the solvent into the Air Supply Hose (Not Included) Trigger (47) Bracket (79) SHINGLE SPACING Screw (80) Nose BOTTOM VIEW Roofing Shingle drive cylinder of the tool. Make sure to dry off the Roofing Nailer before use. Any ...