Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
3. Make sure the trigger and the safety nose mechanism move up and down without sticking. 4. Connect the nailer to the air supply. the safety mechanism is a mechanical device that can fail. never rely on this mechanism as an excuse to point the nailer at yourself or any bystanders. serious injury may occur. 5. Without pressing the trigger, depress the safety nose mechanism against a scrap piece of wood that is clean and free of any knots, nails, or other foreign objects. — if the nailer does not fire, then the safety nose mechanism is working correctly. — if the nailer does fire when you do this, immediately disconnect the nailer from the air supply and call grizzly technical support at (570) 546-9663 for help. — if the nailer fires when the trigger is pulled, without the safety nose mechanism being depressed, then immediately disconnect the nailer from the air supply and call grizzly technical support at (570) 5469663 for help. — if you find that the safety nose mechanism is not working properly, check the lubrication of its sliding components. t21347 2" nailer Kit -7 operations loading When replacing nails in your Model t21347, follow these guidelines: gauge: 18 length: 5.8"–2" Capacity: 100 to load your nailer: 1. disConneCt nAiler FroM the Air supply! 2. sliding magazine pusher back, as shown in figure 3, to lock the catch lever in place. Catch lever figure 3. sliding magazine pusher back and locking catch lever in place. 3. insert a strip of nails, pointed-end down, into the magazine as shown in figure 4. figure 4. loading nails into magazine. 4. slide the nails all the way down to the nose of the nailer. 5. push the magazine pusher all the way in until the catch lever locks. operating if you have not read the safety instructions in this manual, do not operate the nailer. Before you operate your nailer, place five to six drops of the included oil into the quick connect fitting where the nailer connects to the air supply. to operate your nailer: 1. Connect the air supply to the quick connect fitting. 2. to test for proper nail penetration, hold the nailer perpendicular to the surface of a piece of clean scrap wood that is thick enough for the length of nails you have loaded. -8- t21347 2" nailer Kit 3. depress the safety nose mechanism against your workpiece. 4. Before pulling the trigger, make sure your free hand and other body parts are positioned out of the way of a potential path of a nail in case of deflection. deflection is caused when grain irregularities, knots or foreign objects inside the wood cause the nail to change its path, resulting in the nail puncturing the surface of the workpiece, as shown in figure 5. Besides damaging your workpiece, deflection can cause injury if your free hand is securing the workpiece in the location that the nail deflects. figure 5. example of nail deflection. 5. pull the trigger. — if the nail drove into the wood far enough, continue with your intended operations. — if the nail either went too far or not far enough, then go to the adjusting depth subsection on this page. adjusting depth A depth adjustment knob is attached to the nose for setting the nail depth. to adjust the depth: 1. disConneCt nAiler FroM the Air supply! 2. rotate the adjustment knob (figure 6) clockwise to drive the nails deeper or counterclockwise to drive the nails shallower. figure 6. depth adjustment controls. safety nose Adjustment Knob 3. Connect nailer to the air supply and test the nail depth, and repeat this entire procedure if necessary until the nail depth is satisfactory. t21347 2" nailer Kit -9 clearing Jammed nails A jammed nail must be cleared before using the nailer again. to clear a jammed nail from the discharge area: 1. disConneCt nAiler FroM the Air supply! 2. release the catch lever and slide the magazine pusher back. 3. remove the nail stick from the magazine. 4. open the nailer nose by removing the rubber nose tip, depressing the nose release mechanism, and opening the nose cover as shown in figure 7. figure 7. nose opened to clear a jam. nose Cover nose tip nose release Clip 5. dislodge the jammed nail with a tool that will fit in the slot on the underside of the nose. 6. throw the damaged nail away and insert a new nail stick that only contains clean, undamaged nails. do not use dirty or damaged nails! 7. slide the pusher back until it locks into position. -10- t21347 2" nailer Kit replacing pistons & o-rings if you use your nailer day in and day out, repair pistons are cheap insurance against wasted down time and lost profits, in the event that a piston or piston shaft becomes worn out. the piston & o-ring repair Kit, part pt21347087, may be purchased for the Model t21347 from grizzly. always disconnect air from nailer whenever servicing! during maintenance, a nailer connected to air may fire accidentally, causing serious personal injury! to replace a piston: 1. disConneCt nAiler FroM the Air supply! 2. remove all nails from the magazine cartridge. 3. remove the four...