Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
DO NOT use dirty or damaged nails in your nailer! -8- H5571 34° Framing Nailer Kit Cleaning Nailer Use a good solvent to clean the nose assembly of the nailer. Always be sure that the nailer is dry before using it again. Do not allow dust, chips, sand, etc. into the air connectors or into the body of the nailer; this may result in leaks and damage to the nailer and the air fittings. Never use gasoline or other flamma- ble liquids to clean this tool. Vapors in the tool may ignite, causing the tool to explode. Ignoring this warning may lead to serious personal injury or even death! Always disconnect air from nailer whenever servicing! During mainte- nance, a nailer connected to air may fire accidentally, causing serious personal injury! H5571 34° Framing Nailer Kit -9 Replacing Pistons/O-Rings If you use your nailer day in and day out, Grizzly offers repair pistons as cheap insurance against wasted down time and lost profits in the event that a piston or piston shaft becomes worn out. Always disconnect air from nailer whenever servicing! During mainte- nance, a nailer connected to air may fire accidentally, causing serious personal injury! To replace a piston: 1. Disconnect the nailer from the air supply! 2. Remove all nails from the magazine cartridge. 3. Remove the 4 cap screws from the nailer exhaust cap. 4. Remove the exhaust cap as shown in Figure 6. Figure 6. Removing nailer exhaust cap. -10 5. The top of the piston should now be visible inside the cylinder, which is housed in the head of the nailer. 6. Open the magazine. 7. Watch the discharge area and push the top of the piston with your finger. You will see the piston shaft slide down the discharge area. 8. With a long flathead screwdriver or similarly shaped tool, push the piston shaft back inside the nailer until you can grip the piston head and remove it from the cylinder. (Be careful not to scratch the discharge area when pushing the piston shaft with the screwdriver.) 9. Place a new O-ring on the new piston and apply a thin film of the nailer lubricating oil on the O-ring. 10. Insert the new piston in the cylinder. Make sure that the grooves on the piston shaft line up with those on the guide at the bottom of the cylinder. The new piston should easily slide into the cylinder. DO NOT force the piston into the cylinder! If the piston is not easily inserted, double-check the alignment of the piston shaft with the grooves on the guide. 11. After the piston is inserted correctly, close the magazine. Replace the rear cap assembly and tighten the 4 cap screws. 12. For more assistance, or to install a complete O-ring set, refer to the appropriate breakdown diagram in the back of this manual. H5571 34° Framing Nailer Kit H5571 34° Framing Nailer Kit -11- H5571 PART BREAKDOWN 25 95 68 84 65 85 67 88 30 28 27 59 26 39 40 38 37 7 92 91 56 24 30 35 29 83 28 82 31 35 66 35 62 97 96 63 64 73 82 74 80 89 90 36 32 34A 85 61 6 5 4 2 7 1 23 22 19 21 20 16A 21-1 100 50 49 48 47 45 46 44 42 43 41 53A 52 51 78 72 58 57 10 12-1 8 9 12-1 14 13 12 11 60 87 70 15-1 15-2 REF PART # DESCRIPTION REF PART # DESCRIPTION 1 PSB115M BTN HD CAP SCR M6-1 X 16 2 PH5571002 EXHAUST COVER 4 PH5571004 RUBBER WASHER 10MM 5 PSB06M CAP SCREW M6-1 X 25 6 PH5571006 CAP 7 PW09M FLAT WASHER 7MM 8 PH5571008 SPACER 9 PH5571009 PISTON STOPPER 10 PH5571010 SPRING 11 PH5571011 O RING 12 PH5571012 PISTON HEAD VALVE 12-1 PH5571012-1 SPACER 13 PH5571013 O RING 14 PH5571014 SEAL 15-1 PH5571015-1 O RING 15-2 PH5571015-2 O RING 16A PH5571016A PISTON ASSEMBLY 19 PH5571019 CYLINDER RING 20 PH5571020 O RING 21 PH5571021 CYLINDER 21-1 PH5571021-1 O RING 22 PH5571022 BUMPER UPPER 23 PH5571023 GASKET 24 PH5571024 BODY 25 PH5571025 BUMPER BOTTOM 26 PH5571026 O RING 27 PH5571027 NOSE 28 PSB31M CAP SCREW M8-1.25 X 25 29 PH5571029 PIN 30 PH5571030 RUBBER RING 31 PSB116M BTN HD CAP SCR M5-.8 X 14 32 PH5571032 GUIDE SAFETY LEVER 34A PH5571034A SAFETY LEVER ASM. 35 PLN02M LOCK NUT M5-.8 36 PH5571036 SPRING 37 PH5571037 SAFETY LEVER 38 PLN03M LOCK NUT M6-1 39 PH5571039 DEPTH ADJUSTING KNOB 40 PH5571040 RUBBER PAD 41 PH5571041 O RING 42 PH5571042 O RING 43 PH5571043 VALVE 44 PH5571044 O RING 45 PH5571045 O RING 46 PH5571046 O RING 47 PH5571047 VALVE PLUNGER 48 PH5571048 O RING 49 PH5571049 SPRING 50 PH5571050 PLUNGER 51 PH5571051 O RING 52 PH5571052 PLUNGER CAP 53A PH5571053A TRIGGER ASSEMBLY 56 PH5571056 PUSHER 57 PH5571057 STOPPER 58 PH5571058 SPRING 59 PH5571059 GASKET 60 PH5571060 SET PIN 61 PSB26M CAP SCREW M6-1 X 12 62 PH5571062 SPIRAL SPRING 63 PH5571063 ROLLER 64 PH5571064 BALL PIN 65 PH5571065 MAGAZINE 66 PH5571066 NAIL GUIDE LINER 67 PSB26M CAP SCREW M6-1 X 12 68 PH5571068 DEBRIS SHIELD 70 PH5571070 STOPPER BLOCK 72 PSB117M BTN HD CAP SCR M5-.8 X 8 73 PH5571073 BRACKET 74 PLN04M LOCK NUT M8-1.25 78 PSB116M BTN HD CAP SCR M5-.8 X 14 80 PH5571080 3/8" NPT CONNECTOR 82 PW01M FLAT WASHER 8MM 83 PH5571083 GASKET WASHER 84 PH5571084 PIN 85 PH5571085 SPACER 87 PH5571087 PISTON GUIDE WASHER 88 PLW04M LOCK WASHER 8MM...