Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
3. Pull back the magazine cover until it stops. 4. Point the stapler up and insert a stick of staples into the magazine as shown in Figure 3. Make sure that the pointed ends of the staples point in the same direction as the stapler nose piece. Figure 2. Releasing magazine latch. Figure 3. Loading staples into stapler. 5.Push the magazine cover forward until the magazine latch locks in place. -6- H5626/H5627 Upholstery Stapler Operating Stapler If you have not read the safety instructions in this manual, do not operate the stapler. Every time you operate your stapler, place one drop of the included oil into the quick connect fitting where the stapler connects to the air supply. To operate your stapler: 1. Connect the air supply to the quick connect fitting. 2. Test the loaded stapler for proper penetration. Hold the stapler perpendicular to the surface of a piece of clean scrap wood that is thick enough for the length of staples you have loaded. 3. Before pressing the trigger, make sure your free hand is positioned out of the way of a potential path of a staple in case of deflection. (Deflection is caused when the staple changes its path, resulting in the staple puncturing the surface of the workpiece as shown in Figure 4.) Figure 4. Example of staple deflection. Besides damaging your workpiece, deflection can cause injury if your free hand is securing the workpiece in the location that the staple deflects. 4. Press the trigger. If the staple drove into the wood far enough, continue with your intended operations. If the staple either went too far or not far enough, then adjust the air pressure. More air pressure will make the staple go deeper and less air pressure will decrease the staple penetration. H5626/H5627 Upholstery Stapler -7 Speed Adjustment The Model H5627 features staple firing speeds from .5 to 16 staples per second. To adjust the staple firing speed: 1. Disconnect the stapler from the air supply! 2. Release the speed adjustment lock by holding the speed adjustment screw in place with a screwdriver while rotating the speed adjustment lock counter clockwise. 3. Rotate the speed adjustment screw counter clockwise to increase the firing speed or clockwise to slow the firing speed (Figure 5). Fast Slow Figure 5. H5627 speed adjustment screw. Speed Adjustment Lock Speed Adjustment Screw 4. To test fire the stapler push the stapler against a scrap of wood, hold the trigger down continuously, and move the stapler across the wood. 5. When the firing speed has been adjusted, secure the speed adjustment screw by placing a flat head screwdriver in the slot and twisting the speed adjustment lock clockwise until tight. Clearing Jammed Staples A jammed staple must be cleared before using the stapler again. To clear a jammed staple: 1. Disconnect the stapler from the air supply! 2. Open the magazine cover and pull the magazine all the way back. 3. Remove stick of staples. 4. Remove jammed staple with needle nose pliers. Always disconnect air from stapler whenever clearing a jammed staple! -8- H5626/H5627 Upholstery Stapler Cleaning Stapler Use a good solvent to clean the nose assembly of the stapler. Always be sure that the stapler is dry before using it again. Do not allow dust, chips, sand, etc. into the air connectors or into the body of the stapler; this may result in leaks and damage to the stapler and the air couplings. Never use use gasoline or other flammable liquids to clean this tool. Vapors in the tool may ignite, causing the tool to explode. Ignoring this warning may lead to serious personal injury or even death! Always disconnect air from stapler whenever servicing! During maintenance, a stapler connected to air may fire accidentally, causing serious personal injury! H5626/H5627 Upholstery Stapler -9 Replacing Pistons/O-Rings If you use your stapler day in and day out, Grizzly offers repair pistons as cheap insurance against wasted down time and lost profits in the event that a piston or piston shaft becomes worn out. Always disconnect air from stapler whenever servicing! During maintenance, a stapler connected to air may fire accidentally, causing serious personal injury! To replace a piston: 1. Disconnect the stapler from the air supply! 2. Remove all staples from the magazine cartridge. 3. Remove the 4 cap screws from the stapler exhaust cap on the Model H5626, or unscrew the exhaust cap on the Model H5627. 4. Remove the exhaust cap as shown in Figure 6. 5. The top of the piston should now be visible inside the cylinder, which is housed in the head of the stapler. 6. Open the magazine. Figure 6. Removing stapler exhaust cap. 7. Watch the discharge area and push the top of the piston with your finger. You will see the piston shaft slide down the discharge area. 8. With a long flathead screwdriver or similarly shaped tool, push the piston shaft back inside the stapler until you can grip the piston head and remove it from the cylinder. (Be careful not to scratch the discharge area when pushing the...