Stimmen - 2, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
If the stapler does not fire, then the safety yoke mechanism is working correctly. If the stapler does fire when you do this, immediately disconnect the stapler from the air supply and call our customer service for help. Similarly if the stapler fires when the trigger is pulled, without the safety yoke mechanism being depressed, then the stapler is not working properly. If either of these two conditions develop after you have used your stapler for a period of time, check the lubrication of these mechanisms. The safety yoke is a mechanical device that can fail. Never rely on the safety yoke mechanism as an excuse to point the stapler at yourself or any bystanders. Serious injury may occur. -5- H2909 18 Gauge Stapler Kit OPERATION Loading Stapler To load your stapler: 1. Disconnect the air supply from the stapler! 2. Push the magazine latch in the direction shown in Figure 1. Figure 1. Releasing magazine latch. 3. Pull back the magazine cover until it stops. 4. Point the stapler up and insert a stick of staples into the magazine as shown in Figure 2. Make sure that the pointed ends of the staples point in the same direction as the stapler nose piece. Figure 2. Loading staples into stapler. 5. Push the magazine cover forward until the magazine latch locks in place. Depth Adjustment 1. Rotate the depth adjustment wheel (shown in Figure 3) clockwise to increase the nail depth. 2. Rotate the finger wheel counter-clockwise to decrease the nail depth. Figure 3. Depth adjustment wheel. Operating Stapler If you have not read the safety instructions in this manual, do not operate the stapler. Before you operate your stapler, place one drop of the included oil into the quick connect fitting where the stapler connects to the air supply. Fire the EMPTY stapler 3-4 times before beginning, so oil does not come out onto the project during regular operation. H2909 18 Gauge Stapler Kit -6 To operate your stapler: 1. Connect the air supply to the quick connect fitting. 2. Test the loaded stapler for proper penetration. Hold the stapler perpendicular to the surface of a piece of clean scrap wood that is thick enough for the length of staples you have loaded. Depress the safety yoke mechanism on your workpiece. 3. Before pressing the trigger, make sure your free hand is positioned out of the way of a potential path of a staple in case of deflection. (Deflection is caused when the staple changes its path, resulting in the staple puncturing the surface of the workpiece as shown in Figure 4.) Figure 4. Example of staple deflection. Besides damaging your workpiece, deflection can cause injury if your free hand is securing the workpiece in the location that the staple deflects. 4. Press the trigger. If the staple drove into the wood far enough, continue with your intended operations. If the staple either went too far or not far enough, then adjust the air pressure. More air pressure will make the staple go deeper and less air pressure will decrease the staple penetration. Clearing Jammed Staples The most frequent situation with any type of stapler is a staple jam. A jammed staple must be cleared before using the stapler again. The two places where a staple can get jammed are the magazine and the discharge area. Always disconnect air from stapler whenever clearing a jammed staple! To clear a jammed staple from the magazine: 1. Disconnect the stapler from the air supply! 2. Open the magazine cover and pull the magazine all the way back. 3. Locate and remove the jammed staple with a pair of needle nose pliers. Close the magazine cover so it latches. To clear a jammed staple from the discharge area: 1. Disconnect the stapler from the air supply! 2. Remove all of the staples from the magazine. 3. The jammed staple should now be visible; remove it from the discharge area with needle nose pliers. 4. Replace the staples. Push the magazine closed and snap the quick release latch back into operating position. -7- H2909 18 Gauge Stapler Kit Oiling Stapler Special oil has been included with your new Grizzly stapler to help maintain its useful life. Place one drop of oil in the stapler air inlet (as shown in Figure 5) before every use. Wipe off any excess oil near the stapler exhaust to avoid dust build-up. When the oil that was included with the stapler has been completely used, replace with Grizzly Model G2820 Pneumatic Tool Oil. Another option to manual oiling would be to install a lubricator in your air compressor line. If your air compressor line already has a lubricator, then regular lubrication of your stapler will not be necessary. Just make sure there is always oil in the lubricator. As mentioned before, the best option is to install a filter/lubricator/regulator unit such as the Grizzly Model H2333 in your air line. Figure 5. Lubricating stapler via air inlet. Cleaning Stapler Use a good solvent to clean the nose assembly of the stapler. Always be sure that the stapler is dry before using it again. Do not allow dust, chips, sand, etc. i...