Stimmen - 2, Durchschnittliche Bewertung: 5
(
)
)
|
Anleitung Zusammenfassung
6. Watch the discharge area and push the top of the piston with your finger. You will see the piston shaft slide down the discharge area. Model H8232 3-Piece Framing/Finish/Palm Nailer Kit -13 7. Taking care not to scratch or dent the nailer parts, use a wooden dowel or similarly shaped tool to push the piston shaft back inside the nailer until you can grip the piston head and remove it from the cylinder. Clean and inspect the parts for cracks, wear, or burrs. 8. Apply a thin film of pneumatic tool oil on the new O-ring and place it on the new piston. 9. Insert the new piston in the cylinder. Make sure that the grooves on the piston shaft line up with those on the guide at the bottom of the cylinder. The new piston should easily slide into the cylinder. DO NOT force the piston into the cylinder! If the piston is not easily inserted, double-check the alignment of the piston shaft with the grooves on the guide. 10. After the piston is inserted correctly, close the magazine. Replace the rear cap assembly and secure it with the four cap screws removed in Step 3. Note: For more assistance, or to install a complete O-ring set, refer to the appropriate breakdown diagram in the back of this manual for component locations. Palm Nailer To replace a piston for your palm nailer: 1. DISCONNECT NAILER FROM THE AIR SUPPLY! 2. Using a 19mm wrench, remove the nose piece, depth guide, compression spring, and flat washer. 3. Use the 4mm hex wrench to remove the four cap screws on the nailer cap, 4. Push the ram pin towards the inside of the nailer—this will push the cylinder free of the housing. 5. Grab the ram pin and pull the piston from the cylinder. 6. Apply a thin film of pneumatic tool oil on the new O-ring and place it on the new piston. 7. Insert the new piston into the cylinder. The new piston should easily slide into the cylinder. DO NOT force the piston into the cylinder! If the piston is not easily inserted, check the alignment of the piston inside the cylinder. 8. After the piston is inserted correctly, place the cylinder back in the nailer housing. If seated correctly, the cylinder will snap into place. 9. Push the cylinder collar down into the housing as far as it will go. The horizontal air slots on the cylinder sides should be visible. 10. Replace the rear cap and secure it with the four cap screws removed in Step 3. 11. Re-install the flat washer, compression spring, depth guide, and nose piece onto the front of the nailer, then use a 19mm wrench to tighten the nose piece. Note: For more assistance, or to install a complete O-ring set, refer to the appropriate breakdown diagram in the back of this manual for component locations. -14- Model H8232 3-Piece Framing/Finish/Palm Nailer Kit CLEANING & LUBRICATION Cleaning Lubricating Use non-flammable solvent to clean the nose assembly of the nailer. Always be sure that the nailer is dry before using it again. Do not allow dust, chips, sand, etc. into the air connectors or into the body of the nailer; this may result in leaks and damage to the nailer and the air couplings. Never clean this tool with gasoline or other flammable liquids. Vapors in the tool may ignite, causing the tool to explode. Ignoring this warning may lead to serious personal injury or even death! Standard pneumatic tool oil has been included with your new Grizzly nailer to help maintain its useful life. Place two to six drops of oil in the nailer air inlet (as shown in Figure 12) before every use, or after 2 hours of continuous use. Wipe off any excess oil near the nailer exhaust to avoid dust build-up. When the oil that was included with the nailer has been completely used, replace it with Grizzly Model G2820 Pneumatic Tool Oil. Another option to manual oiling would be to install a lubricator in your air compressor line. If your air compressor line already has a lubricator, then regular lubrication of your nailer will not be necessary. Just make sure there is always oil in the lubricator. Figure 12. Lubricating nailer via air inlet. Model H8232 3-Piece Framing/Finish/Palm Nailer Kit -15 -16- Model H8232 3-Piece Framing/Finish/Palm Nailer Kit H8232 PARTS .. .. .. .. .. .. .. .. .. .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... ........ ........ ........ Framing Nailer Parts Breakdown Framing Nailer Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION PSB31M CAP SCREW M8-1.25 X 25 PH8233002 EXHAUST PORT PH8233003 SPACER PH8233004 CIRCULAR SPRING PH8233005 RETAINING RING PSB06M CAP SCREW M6-1 X 25 PLW03M LOCK WASHER 6MM PH8233008 CYLINDER PLUG PSS07M SET SCREW M5-.8 X 5 PH8233010 CYL...