Stimmen - 1, Durchschnittliche Bewertung: 5
(
)
)
|
Anleitung Zusammenfassung
Indicates an imminently hazardous situation which, if not avoided, WILLresult in death or serious injury. This symbol is used to alert the user to useful infor- mation about proper operation of the equipment.NOTICE Safety Instructions For Pneumatic Tools 1. KEEP ALL SAFETY DEVICES IN 5. KEEP CHILDREN AND VISITORS PLACE and in working order. AWAY. All children and visitors 2. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of check- should be kept at a safe distance from work area. ing to see that keys and adjusting 6. MAKE WORKSHOP CHILD wrenches are removed from tool PROOF by locking your shop and before operation. shutting off air valves. 3. KEEP WORK AREA CLEAN. 7. DO NOT FORCE TOOL. It will do Cluttered areas and benches invite the job better and safer at the rate accidents. for which it was designed. 4. DO NOT USE IN DANGEROUS 8. USE THE RIGHT TOOL. Do not ENVIRONMENT. Do not use pneuforce tool or attachment to do a job matic tools in damp or wet locafor which it was not designed. tions, or where any flammable or 9. DO NOT USE UNDER THE noxious fumes may exist. Keep INFLUENCE OF DRUGS OR work area well lighted. ALCOHOL. Safety Instructions For Pneumatic Tools 10. USE PROPER AIR HOSE for the 17. DISCONNECT TOOLS before sertool. Make sure your air hose is in vicing, changing accessories, or good condition and is long enough to moving to another location. reach your work without stretching. 18. DO NOT OVERREACH. Keep 11. WEAR PROPER APPAREL. Do not proper footing/balance at all times. wear loose clothing, gloves, neck-19. USE THE RECOMMENDED ties, rings, bracelets, or other jew-ACCESSORIES. Consult owner’s elry which may get caught in moving manual for recommended accesparts. Non-slip footwear is recom-sories. The use of improper accesmended. Wear a protective hair cov-sories may cause risk of injury. ering to contain long hair. 20. CHECK FOR DAMAGED PARTS 12. ALWAYS USE SAFETY GLASSES. BEFORE USING. Check for bind- Also use a face or dust mask if oper-ing and alignment of parts, broken ation is dusty. Everyday eyeglasses parts, part mounting, loose bolts, only have impact resistant lenses, and any other conditions that may- they are NOT safety glasses. affect machine operation. Repair or 13. WEAR APPROVED HEARING replace damaged parts. PROTECTION. Air escaping from 21. NEVER LEAVE UNATTENDED pneumatic tools can exceed safe TOOL CONNECTED TO AIR. exposure limits and may cause Disconnect the air hose and do not hearing damage with prolonged leave tool until it is relieved of any exposure. built up pressure. 14. SECURE WORK. Use clamps or a 22. NEVER ALLOW UNTRAINED vise to hold work when practical. It is USERS TO USE THIS TOOL safer than using your hand and frees WHILE UNSUPERVISED. both hands to operate tool. 23. IF YOU ARE UNSURE OF THE 15. MAINTAIN TOOLS WITH CARE. INTENDED OPERATION, STOP Keep tools lubricated and clean USING TOOL. Seek formal training for best and safest performance. or research books or magazines Follow instructions for lubricating that specialize in pneumatic tools. and changing accessories. 24. BE AWARE OF HOSE LOCATION 16. REDUCE THE RISK OF WHEN USING PNEUMATIC UNINTENTIONAL FIRING. Do not TOOLS. Hoses can easily become carry tool with hand on trigger and a tripping hazard when laid across always disconnect from air when not the floor or spread out in a disorgain use. nized fashion. H6332 11.4" Brad Nailer -1 Additional Safety Instructions for Nailers 1. HAND INJURIES: Do not place your hands near the nail point of entry. A nail can deflect and tear through the surface of the workpiece, puncturing your hand or fingers. 2. COMBUSTIBLE GASES: Never connect the nailer to pressurized oxygen or other combustible gases as a power source. Only use filtered, lubricated, and regulated compressed air. 3. SAFE HANDLING: Never point the nailer at others! Do not keep the trigger pulled when loading fasteners, carrying, or holding tool. Carry the nailer only by the handle, never by any other part. Do not carry the nailer by the air hose. Disconnect the nailer from the air hose when going up and down ladders. 4. CLEANING: Never use gasoline or other flammable liquids to clean the nailer; vapors in the nailer will ignite by a spark and cause it to explode. 5. HOSE USAGE: Make sure your air hose is designed for the tool in use, is in good condition, and is long enough to reach your work without stretching. However, an overly long air hose in the work area may be a tripping hazard. 6. OPERATING QUESTIONS: If you are not sure about the intended operation, stop using the nailer. Seek formal training or research books or magazines that specialize in pneumatic tools. 7. MAINTENANCE: Always disconnect air from the nailer when servicing or installing nails. During maintenance, a nailer connected to air may fire accidentally, causing serious personal injury. 8. COMPRESSED AIR RATING: Do not connect the nailer to compressed air that exceeds 120 PSI. 9. CHECK VALVE: Do not use a check valve or any other fit...