Stimmen - 3, Durchschnittliche Bewertung: 4.7
(
)
)
|
Anleitung Zusammenfassung
! Ideal for removing paint in awkward corners, crevices, mouldings, beading or architraves. Concentrator nozzle G84 Glass protection nozzle -G89 ! Deflects the heat away from glass or other fragile areas. ! Ideal for windowsills, ledges, frames and skirting boards. Glass protection nozzle G89 Hook nozzle -G87 ! Disperses the heat flow evenly around the whole work surface. ! Ideal for defrosting frozen pipes, soldering pipe work, bending plastics or heat shrinking electrical insulating tubing. G87 Hook nozzle Deflector nozzle -G88 ! Directs a long, narrow heat pattern to the work surface. ! Ideal for removing paint or varnish from large, flat surfaces such as skirting boards, doors, stairs etc. ! It should be used in G88 Deflector nozzle conjunction with a flat scraper. ! Vinyl tiles can be removed by softening the tile and adhesive. Removing paint -general Do not heat the paint for too long as this will burn the paint, making it difficult to remove. 1.Choose the required nozzle and fit onto the heat outlet. 2.Hold the gun with nozzle approximately 50mm (2”) from surface of the paintwork. 3.Starting with the low heat setting, move the gun slowly backwards and forwards until the paint blisters and bubbles. 4.Immediately remove the paint with a scraper or shavehook. 5.Aim to heat the paint just ahead of the scraper so that you can develop a continuous action. Removing paint from window frames WARNING – Glass can break easily when heated. 1.Use the glass protection nozzle. 2.Ensure the nozzle is facing the correct way to deflect heat away from the glass before you switch on the heat gun. 3.Rotate the gun/nozzle 90. as you move to horizontal or vertical bead (take care it could be hot!). 4.Paint can be removed by using a shavehook and/or a soft wire brush. Maintenance Always allow the machine to cool down (before storing) and disconnect from the power supply. The heat gun should be cleaned before being stored away by wiping over with a clean damp cloth. DO NOT USE CHEMICALS. Ensure that the ventilation slots are not blocked. Trouble Shooting If a problem occurs always switch off the unit immediately at the mains. My unit fails to work? Check the fuse in the plug is sound and rated 13 amps. If an extension cable is used it must be fully unwound and rated at least 10 amps capacity. 3 MAINS CONNECTION This unit is a Class II appliance which means it is double insulated for your protection. No earthing wire is necessary. If the supply cord is damaged, it must be replaced by Earlex Ltd or our appointed agents. Please read the following safety instructions before use. 1. If the plug is cut off from the mains lead then the plug must be disposed of safely. NEVER under any circumstances insert such a plug into a 13 amp socket-outlet. 2. A replacement fuse must be rated at 13 amp and manufactured and approved to BS 1362. 3. IF IN ANY DOUBT CONTACT A qUALIFIED ELECTRICIAN. If you need to fit a plug to the mains lead, this should be fitted in accordance with the wiring instructions below and will need to be used with a 13 amp fuse. If in doubt consult a qualified electrician. If you are using an extension lead it must be rated at a minimum of 10 amps and fully unwound. Do not operate with a lead rated at less than 10 amps as this will cause premature component failure which is not covered by the guarantee. As the colours of the wires in the mains lead of the application may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black.The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red. INFORMATION ON THE DISPOSAL OF WASTE ELECTRICAL & ELECTRONIC EqUIPMENT kNOWN AS WEEE Your attention is brought to new directives applicable to the disposal of this electrical equipment, where in accordance with the legislation this product must not be disposed of in your normal household waste. Instead it is your responsibility to dispose of this type of waste by handing it over to special designated collection points for recovery and recycling. This product is marked with a ‘Wheelie bin’ symbol with a cross on it to remind you of this action. The objective of this directive is to help conserve resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste please contact your local authority. Take back facilities are free of charge. GUARANTEE This heat gun is guaranteed for a period of 12 months against faulty manufacture or materials. It is not guaranteed for industrial or hire purposes. The nozzles are classed as consumables and are not covered by guarantee. This guarantee does not affect your statutory rights. In the event of any problem occurring please contact us on our Helpline on 01483 454666 Monday-Friday 08:30 -17:00...