1 • Safety precautions...........................2 • Installation and adjustment...........................4 • Install the water inlet hose........................6 • Preparation before using..............................8 • Put in the laundries........................9 • Usage of the detergent.................. 9 • Use the operation buttons..............................10 • Close the top lid..................... 13 • Finish washing.............................. 13 • Disposal after was

inside front cover Matters Needing Attention .......... 1-3 1 nsta 11 at i on ................................... .......... 4-5 Control Panel................................... .............. 6 Operational Functions ................ 7-8 During Use Guide to Operational Program Selection ..........9 Washing Methods ............................. 10-11 Hints for Saving Energy ............ ............. 11 Washing Instructions ................... ............. 12 Other Functions .......

See to the figure: Back Front Bottom plate Screw Soft items Push the lint filter downward to location for lint filter. How to change the direction of the drain hose 1.The height of the drain hose shall be less than 10cm, or the drainage will not be smooth, and cost such long time that the machine may stop at mid way. 2.Do not trample or press the drain hose. If the drain hose is too long, cut it at mid point. To make smooth drainage, cut the front end of the hose slantingly. 4.If extra drain hos

Fill water to preset water level. 3. Rinse Adjust the wash timer to 2-3 minutes to do rinsing. When the laundries quantity is few, please use "STANDARD" current. If you use "STRONG" current, it may splash. Rinsing (Repeat the midway spinning and rinsing with stored water for 2-3 times) 1.Put the laundries into the wash tub. Select suitable current according to the laundries. 2.Adjust the water level Set the water level with water level adjusting lever according to the laundries quantity. Then fi

(Refer to the Guide to Operational Program Selection). Caution: The program knob is at the same time a power button. When the knob is set to Stop , the power is turned off; when the knob is set to other positions, the power is turned on. B Wash temperature knob By turning this knob, the required temperature can be selected (temperatures between 30 -90 can be selected). Refer to the Guide to Operational Program Selection. C Speed knob By turning this knob, the required spinning speed can be selec

Now the washing machine will not drain but start a soaking cycle. And the soaking indicator will blink. If you want to spin the laundry, press this button again, operation will resume. Control pannel 10 7 I Delay wash button Press this button,the washing machine will start to adjust delay time.Each press of the button,the delay will increase 30 minutes.Keep pressing the button and the delay time will keep increasing.The range is 0-24 hours.For example,adjust it to 10 hours,press the "start" butt

HG1000TXVE/ME HG1200TXVE/ME .. .. Technical Specifications 14 MODEL HG1200TXVEME HG1000TXVEME HG800TXVEME Power supply Maxi u working current(A) 10 10 10 ater pressure (MPa) 0.05 < P < 1 0.05 < P < 1 0.05 < P < 1 ashing power( ) 300 250 250 Spinning power( ) 700 530 500 Max. wash load (kg) 5 5 5 Spinning speed (MAX) (r/ in) 1200 1000 800 ash progra 15 15 15 Heating power ( ) 1700 1700 1700 eight (kg) 86 86 86 HG1200TXVEME HG1200TXVE HG1000TXVEME HG1000TXVE HG800TXVEME HG800TXVE 1800 1800 1800 3

3. 4. Laundry treament sort out clothes according to type and extent of dirt. There are three types of clothes: cotton, synthetical and woolen ( silk) fabrics. separate white clothes from colored. If whites and coloreds are combined for one load, make sure the coloreds are colorfast. -Remove all objects from pockets that may cause damage to the machine, such as keys and coins. -Clothing with frayed edges or yarns should be put in a wash bag or special bag before washing. -Repaire damaged clothin

.. HG1000TXVE/ME HG1200TXVE/ME .. .. Technical Specifications 14 MODEL HG1200TXVEME HG1000TXVEME HG800TXVEME Power supply Maxi u working current(A) 10 10 10 ater pressure (MPa) 0.05 < P < 1 0.05 < P < 1 0.05 < P < 1 ashing power( ) 300 250 250 Spinning power( ) 700 530 500 Max. wash load (kg) 5 5 5 Spinning speed (MAX) (r/ in) 1200 1000 800 ash progra 15 15 15 Heating power ( ) 1700 1700 1700 eight (kg) 86 86 86 HG1200TXVEME HG1200TXVE HG1000TXVEME HG1000TXVE HG800TXVEME HG800TXVE 1800 1800 1800

.. HG1000TXVE/ME HG1200TXVE/ME .. .. Technical Specifications 14 MODEL HG1200TXVEME HG1000TXVEME HG800TXVEME Power supply Maxi u working current(A) 10 10 10 ater pressure (MPa) 0.05 < P < 1 0.05 < P < 1 0.05 < P < 1 ashing power( ) 300 250 250 Spinning power( ) 700 530 500 Max. wash load (kg) 5 5 5 Spinning speed (MAX) (r/ in) 1200 1000 800 ash progra 15 15 15 Heating power ( ) 1700 1700 1700 eight (kg) 86 86 86 HG1200TXVEME HG1200TXVE HG1000TXVEME HG1000TXVE HG800TXVEME HG800TXVE 1800 1800 1800