Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Anleitung Zusammenfassung
CONTENTS Specification table the 2nd cover Names of the parts 1 Safety precautions 2 Installation and adjustment 4 Install the water inlet hose 6 Preparation before washing 8 Put in the laundries 9 Usage of the detergent Use the operation button 10 Finish washing 13 Disposal after washing 14 Trouble shooting answer to question 15 Packing list 16 9 Close the top lid 9 Specification table Water level/Water quantity (about) Water Injection pressure 0.03MPa 0.78MPa~ Standard washing / spinning capacity 5.5kg(Washing Powder) 4.0kg(No Washing Powder) . ° I a E . A . 1 Packing list Meaning and description of the symbols Contents marked with that symbol are actions forbidden to perform. Performing of those action may result in damage of the machine or influence the personal safety of the users. Contents marked with that symbol are related to the safety of the product and the personal safety of the users. Please operate in strict conformity to the contents. Names of the parts Warning sign Forbidden sign Screw cover Top lid component Inner cover Detergent box Control panel seat Outer tub cover Balance ring Inner tub Lint filter Pulsator Front control board Cabinet Front door Liquid blenching filler Adjustable leg Drain protective lid Back cover Power cord Fixed leg (3 pieces) Drain protective lid Water inlet valve Water absorption gasket Hook Cabinet handle Drain hose Base frame Attach block Automatic washing machine Between the upper cushion of the washing machine package and the upper seal of the package carton Bottom plate One One Inside the accessory bag One Inside the document bag One Components of the water inlet hose User's manual Inside the document bag One Warranty card Inner cover component One Inside the accessory bag 2 Safety precautions Phenomena The reason How to settle Trouble-shooting answer to question (If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns sometimes. Please confirm again before sending it to repair. Do not repair it by yourself. The digitron displays E0. The safety switch acts, and the spinning cannot work. The digitron displays E3. The water filling does not work, or is slow. After about 15 minutes later, the digital displays E4. The drainage cannot work, or is too slow. The digitron displays E1. It stops running in midway. The digitron displays E2. The top lid is not closed. The top lid is opened during reserve procedure. Close the top lid. Close the top lid. Is the drain hose put down? Is the drain hose blocked? Put down the drain hose. Open and close the top lid once. Clean the foreign material. Open and close The top Lid Once. Are the laundries put slantingly? Is the machine slanting? Reorder the laundries. Close the top lid. Th machine will start running after 10 seconds of being placed horizontally. Is the water tap opened, or is there water supply failure? Is the water inlet valve blocked? Is the water pressure too low? Open the water tap. Push the start/Pause button once. Clean the water inlet valve then push the Start/Pause button once. Push the Start/Pause button once. The water level sensor is bad. Please contact the after-sales service department. The digitron displays E6. The machine does not act Not wash Not spin Is there power failure? Is the power plug inserted tightly? Is the water level reached preset position? Please use it when there's power supply. Insert the power plug tightly. Fill water to the preset position. Is the power plug inserted tightly? Is the top lid closed reliably? Are the laundries set flat? Insert the power plug tightly. Close the top lid. Set the laundries flat. There's abnormal sound inside the machine The water tap leaks Is the machine slanting? Are the laundries put slantingly in spinning? Are there any foreign materials? Adjust the machine to be even Reorder the laundries and close the top lid. Remove the foreign materials. Is the screw of the jointer of water inlet hose loose or awry? Fasten the screw of the jointer properly. Common phenomena Phenomena Explanation Balance the laundries to avoid slanting. The cloth sensor is checking the cloth, it willadd waterafter 48 seconds. The program is setting the drain time. Some time is needed before it starts spinning. The spinning is intermittent when it starts. The wash procedure is paused. The pulsator pauses during water inlet in wash and rinse. There may be some water flowing out of the drain hose in the first use of the machine. Push the PROGRAM button to select SPIN, but it doesn't work. It is to avoid splashing during water inlet. It is the water remained in the factory inspection of performance. The ventilation holes at the bottom Carpet Do not let the machine share one receptacle with other electric appliances. If the plugging into the receptacle is loose, do not use the plug any more. Do not wash water-proof laundries like the raincoat, bike covers etc. to avoid abnormal vibrations in spinning. Please plug the power plug on spec...