Stimmen - 3, Durchschnittliche Bewertung: 3.7
(
)
)
|
Anleitung Zusammenfassung
Problem Possible Cause Remedy The mains plug is not Plug in the mains plug. plugged in. The house fuse has blown. Replace the fuse. The washing machine The door is not correctly Close the door; The lock must does not work. closed. engage audibly. START/PAUSE button not pressed long enough. Keep the START/PAUSE button pressed until the programme begins. Cancel the child safety fea- Door cannot be closed. The child safety feature is set ture (see Section "Child Safety Feature“). The fault code E40 The door is not correctly Close the door correctly. appears. The display closed. Start the programme again. MAIN WASH flashes. Operating Instructions Problem Possible Cause Remedy No water flows. Fault code E10appears. The display RINSE + flashes The washing machine vibrates during operation or is unstable. Water tap is closed. Open the water tap. Close the water tap. Unscrew Filter in screw connection of the hose from the tap, re- the inlet hose is blocked. move the filter and clean under running water Water tap is blocked with Check he water tap and have limescale or is faulty. it repaired if necessary. Remove transport packaging The transport packaging has according to the installation not been removed. and connection instructions. Adjust the feet according to The machine is not level. the installation and connection instructions. There is very little washing in This does not impair the op the drum (e.g. only one eration of the machine. dressing gown). The water could not be completely pumped out before spinning because the drainage hose is kinked or the drain pump is blocked. Check the the drain hose and remove any kink if necessary, or clean the drain pump and, if required, remove foreign bodies from the pump housing. It may be necessary to re- Excessive foaming during the main wash. Probably too much detergent was used. duce the amount of detergent used. Follow the detergent manufacturer's recommendations. Operating Instructions Problem Possible Cause Remedy Water runs out from under the washing machine. The screw connection on the Tighten the inlet hose screw inlet hose is leaking. connection Check the drainage hose and The drainage hose is leaking. replace it if necessary. The washing drain pump Close cover correctly. cover is not correctly closed. Stop the programme and re- Washing is caught in the move the washing caught in door. the door. Restart the programme. The emergency emptying hose is not correctly closed or is leaking. Close the emergency emptying hose correctly (see the section "Carrying out Emergency Emptying"). Call your local Service Force Centre if the emergency emptying hose leaks. Fabric softener was not The conditioner insert in the Clean the detergent dis- washed in, compartcompartment for the condi penser drawer and attach the ment . for conditiontioners is not correctly at- conditioner insert securely. ers is filled with water. tached or is blocked. Pay attention to the maximum load quantity (see Pro- Washing heavily Probably too much washing gramme tables). In the case creased put in the drum. of easy-care fabrics, select the EASY IRON programme. The washing is not sufficiently spun. Water is left in the drum. The fault code E20 appears . The RINSE display flashes. Drain hose is kinked. Remove the kink. Contact your local Service Maximum pump head (dis-Force Centre. For pumping charge height 1m from the heights over 1m a conver appliance's base) is exceeded. sion kit is available as a special accessory. Switch off the appliance and Drain pump is blocked. pull out the mains plug. Clean the drain pump. Operating Instructions Problem Possible Cause Remedy The door cannot be opened when the appliance is switched on. Remnants of detergent are building up in the detergent dispenser drawer. The door is locked due to a high water level or a high temperature. (the DOOR display is off). Power failure! (All displays have gone off.) For safety reasons the door remains locked for 4 to 5 minutes. Wait until the DOOR display lights up green. If it is still necessary to open the door: turn the programme selector to OFF turn the programme selector to PUMP OUT. Press the START/PAUSE button After the water has been pumped out, the door can be opened. If water can be seen through the window in the door, first carry out emergency emptying (see section “Carrying out Emergency Emptying Operation"). After approx. 4 to 5 minutes the door can be opened again by pulling the handle. Water tap is not fully Open the water tap fully. opened. Close the water tap. Unscrew The inlet hose filter in the the inlet hose from the water coupling inlet hose at the tap and from the appliance. tap is blocked. Clean the filter. The cause is probably a de- No negative effect on the The rinsing water is tergent with a high silicate rinsing results, use a liquid cloudy. content. detergent if necessary. When pressing a pro- The selected programme op gramme option button tion cannot be combined Make another selection. the correspondi...