Stimmen - 4, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Acidic gas can damage the fuel system of an engine while in storage. ,_ CAUTION:blended fuels (called gasohol or using ethanol 7 Toaddfueltoengine: • Clean area around fuel cap, remove cap. • Add regular unleaded gasoline, slowly,to the fuel tank. Important: Never mix oil with gasoline. • Installfuel cap and wipe up any spilled gasoline. TO START THE CLEANING SYSTEM The best way to start your cleaning system engine for the first time is to follow these instructionsstep-bystep. This starting information also applies whenever you start the engine after you have let the cleaning system sit idle for at least a day. • Place the cleaning system in an area close enough to an outside water source that can flow at ;_rate of at least 3 gallons per minute. Connect a garden hose to the water spout. • Check that the high pressure hose is tightly connected to the spray gun and to the pump. See ASSEMBLY section on page/4. • Check inlet screen on the water inlet. If the screen is dirty, clean before attaching a garden hose. If the screen is damaged, do not connect to the garden hose. Replace with screen provided in maintenance kit or call 1-800-366-PART to order a replacementinlet screen. • Attach the the garden hose to the water inlet. • Tum on the water. Important: Do not run pump without the water supply connected and turned on. You must follow this caution or the pump will be damaged. • Remove the adjustable nozzle extension from the spray gun. • Pull the trigger on the spray gun and hold until a steady stream of water appears. • Engage the safety latch on the spray gun. Safety Latch • Attach adjustable nozzle extension onto spray gun. • Pull choke lever all the way out to the =FULL CHOKE POSITION." Choke Lever in =Full Choke Position" Note: If restarting a warm engine after a short shutdown, move choke lever to =NO CHOKE PosmoN." • Move Run/Stop switch to the "1" or on position. 8 • Grasp starter handle and pull slowly until you feel some resistance. Then pull cord rapidly to overcome compression, prevent kickback and start the engine. Let rope return to starter slowly. Note: The Pressure CommandTM may be placed in any positionduring starting or operation. • When engine starts, move choke lever to "1/2 CHOKE" until engine runs smoothly and then to "NO CHOKE POSITION." If engine falters, move choke lever to =1/2 CHOKE" untilengine runs smoothly and then to "NO CHOKE POSITION." Note: If the engine fails to start after 3 pulls, move choke lever to "NO CHOKE POSITION" and pul! starter rope again. Note: If engine fires, but does not continue to run, move choke lever to "FULL CHOKE" and repeat, starting instructions. • Once the engine has started, disengage the slSray gun safety latch. HOW TO STOP YOUR PRESSURE WASHER Important: Do not run pump without the water supply connected and turned on. You must followthis caution or the pump will be damaged. • Move the Run/Stop switch to the "0" or OFF position. • Simply shutting off the engine will not release pressure in the system. Squeeze trigger on the spray gun to relieve pressure in the hose. Note: A small amount of water will squirt out when you release the pressure. • Rotate the Dial-A-Cleaner TM selector knob to the OFF position to prevent chemical leakage. SIPHONING We recommend that you DO NOT siphon standing water for your water supply. Contaminated, brackish or dirty water can damage the pump. Connect only to household water supply. TIPS • Never use the garden hose inlet to siphon detergent or wax. • If you hold the spray nozzle too far away from the object being cleaned, washing will not be as effective. • Always store the cleaning system with the Dial-A- Cleaner TM selector knob at the OFF position. 9 CUSTOMER RESPONSIBILITIES MA|t_RENANCESCHEDULE HOURLY OPERATING RLL iN DATESAS YOU COMPLETE SERVICE DATES INTERVAL REGULARSERVICE Before Es_tl HOURS or Hours O_ J Eve/'] 50 Evee/100 MAINTENANCE TASK Use Yearly Yearly PRESSURE WASHER Check/clean water inlet screen onquick-connect. xt Checkhighpressurehose. x ' x Check detergent hose, x Check spray gun and assembly for leaks. Purgepumpofairandconterninants. x ENGINE Checkoillevel. x Change engine oil. x* Serviceaircleaner. x'* Clean/replace spark plug. x Prepare for storage. Prepare unitforstorageif itisto remainidleforlonger than30days. "t C_ean i1 clogged. Re_ if perforated or torn. Change oil after the first (2) opera_ng hours and every 50 hours thereafter. Change sooner when operating under dirty or dusty conditions. "* Replace more often under dirty or dusty conditions. PRODUCT SPECIFICATIONS In the State of California a spark arrestor is required by law (Section 4442 of the Califomia Public Pressure Washer Specifications Resources Code). Other states may have similar laws. Federal laws apply on federal lands. PRESSURE 2250 psi Note: if you equip the engine of your cleaning system FLOW RATE 2.5 GPM with a spark arrestor muffler, the spark arrestor must be maintained in effective working order by the CHEMICAL MIX Use ...