Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
1 Remove the machine from the transport base. Remove wedge . (Figure1). 2 Remove the 4 screws . with a screwdriver (Figure2.1). 3 Remove transport securing device . Remove both screws . (Figure2.2)using a number 10 or 13 spanner (depending upon the model). Check to see that both plastic inserts on the connecting carrier have also been removed. Reinstall screws . in their original positions. 4 Both holes must be covered with the caps provided . (found in the accessories package) (Figure 2.3)! Figure 1 Figure 2.1 Figure 2.2 Figure 2.3 1 2 A 12 6 Removing the transport securing devices 5 Remove the . securing device (Figure 3). 6 Remove hose bracket . and cover the To do this: holes with the caps provided . (found in -Remove securing device . the accessories package) (Figure4)! -Remove securing device . -Release the drum doors, locked in the lower position, by pressing down on both eaves simultaneously. Figure 3 Figure 4 F b . G a a . b We recommend retaining all transport securing devices since these will have to be reinstalled for any later possible transport of the appliance. Moving the appliance (depending upon the model) If the machine is fitted with hidden castors, it can easily be moved. To place the machine on the castors, turn the lever on the bottom to the left until it encounters a limit stop (Figure 5). During operation, the machine must always rest firmly on its feet (lever to the right). Before leaving the factory, the washing machine was carefully inspected. It is possible that some water from testing remains in the appliance or in the detergent compartments. Figure 5 7 Connections Cold water supply Connect water-inlet hose (Figure 6). -Minimum water pressure: 0.1 MPa or 1 bar -Maximum water pressure: 1 MPa or 10 bar Drain Mount drain hose with the supplied elbow, connect to a vented drain (Figure 7.1 / 7.2). The elbow must be between 65 and 90 cm above the floor. Secure drain hose against slipping off. Replacing the water-inlet hose After replacement, check to ensure connections are tight and that there are seals on both ends. Regularly check the condition of the water-inlet and drain hose. Replace damaged hoses only with original replacement parts which are available through Customer Service. Figure 6 Figure 7.1 Figure 7.2 min. 10 mm 3/4” 8 Connections Electrical connections Connect the washing machine only to alternating current via a properly installed earthed socket. The mains voltage must correspond to the voltage specification on the washing machine (identification plate). Connection specifications as well as the required fuses are stipulated on the appliance identification plate. Ensure that: • the mains plug and socket are compatible, • the cable cross-section is adequate, • the earthing system has been installed correctly. Installation Safety Instructions Risk of Injury! The washing machine is very heavy. Take care when lifting it. Frozen hoses may tear or burst. Do not install the washing machine in an area where there is a risk of freezing or outdoors. Do not lift up on any protruding components. The washing machine may be damaged. In addition to the safety information listed here, the local water and electricity supplier may have special requirements. If in doubt, have the appliance connected by a specialist. Installation surface Stability is important so that the washing machine does not "wander" during spin cycles. Surfaces used for installation must be solid and even. Soft floor coverings are not recommended, i.e. carpets or floors with foam backing. Changing the mains lead For reasons of safety, the mains lead is only to be replaced by Customer Service which is authorised to do so. Do not use multiple plugs/sockets or extension cables. If a residual current circuit breaker is used, only use one that has this symbol: . Only this symbol can guarantee compliance with all applicable regulations. Do not insert/pull out the mains plug with wet hands. Do not pull out the mains plug by tugging the cable. Figure 8 Adjustable feet: (depending upon the model) Some appliances have two adjustable feet available at the front with can be used to correct for surface unevenness. Level and stabilise the machine in the following manner: - Tip the washing machine gently backwards. - Depending upon the type of floor, rotate the foot or feet in or out (Figure 8). - Check the washing machine for stability. 9 International Laundry Care Symbols In order to assist you in caring for your clothes, these carry a label with the necessary information. The information is given by the following symbols: WASHING (Washtub) 95 95 60 60 40 40 40 30 Normal washing program me Gentle washing program me Normal washing program me Gentle washing program me Normal washing program me Gentle washing program me Special Gentle washing programme Gentle washing program me Hand washing Do not wash The values in the washtub correspond to the maximum water temperatures that are not to be exceeded. A line below the wash...