Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
Rust stains - use chlorine-free cleaning agent, not steel wool. .. Descaling Ensure there is no laundry in the machine This should not be necessary if the correct detergent dosage has been used. If it is necessary, however, proceed according to the descaling agent manufacturer's instructions. Suitable descalers can be obtained via our website or from our after-sales service (.. page 13). Information on the indicator lights model-dependent A signal sounds and indicator lights for the spin speed flash: ¤ ¤¤ ¤¤ ¤¤ ¤¤ Close the washing machine door properly; laundry may be caught. ¤ ¤¤ ¤¤ ¤¤ ¤¤ Turn the tap on; supply hose kinked/trapped; Clean the filter .. page 11, water pressure too low. ¤ ¤¤ ¤¤ ¤¤ ¤¤ Clean the detergent solution pump, page 11, waste pipe/drainage hose blocked. ¤ ¤¤ ¤¤ ¤¤ ¤¤ Water in the base tub, appliance leaking. Call the after-sales service. ¤ ¤¤ ¤¤ ¤¤ ¤¤ or ¤ ¤¤ ¤¤ ¤¤ ¤¤ or ¤ ¤¤ ¤¤ ¤¤ ¤¤ Motor fault. Call the after- sales service. Other displays: Switch off the appliance, wait for 5 seconds and switch it back on. If the display appears again, call customer services .. Installation instructions page 13. . Risk of electric shock. Disconnect the mains plug. . Risk of explosion. No solvents. 11 Information about blockages Detergent solution pump Turn the programme selector to Off and disconnect the mains plug. 1. Open and remove the service flap. 2. Take the drainage hose out of the retainer. Remove the sealing cap, allow the detergent solution to flow out. Push the sealing cap back on. 3. Unscrew the pump cover carefully (residual water). 4. Clean the interior, pump cover thread and pump housing (the impeller in the detergent solution pump must be able to rotate). 5. Replace the pump cover and screw it on tightly. The handle points upright. Replace the drainage hose in the holder. 6. Refit the service flap and close it. To prevent unused detergent from flowing straight into the drain during the next wash: Pour 1 litre of water into compartment II and start the .. Empty programme. Drainage hose at the siphon Turn the programme selector to Off and disconnect the mains plug. 1. Loosen the hose clamp, remove the drainage hose carefully (residual water). 2. Clean the drainage hose and siphon connecting piece. 3. Reattach the drainage hose and secure the connection with the hose clamp. Filter in the water supply Risk of electric shock Do not immerse the AquaStop safety device in water (it contains an electric valve). Reduce the water pressure in the supply hose: 1. Turn off the tap. 2. Select any programme (except for .. Spin/.. Empty). 3. Select .. Start/Pause. Let the programme run for approximately 40 seconds. 4. Turn the programme selector to Off. Disconnect the mains plug. 5. Clean the filter: Disconnect the hose from the tap. Clean the filter with a small brush. and/or for Standard and Aqua-Secure models: Remove the hose from the rear of the appliance. Remove the filter with pliers and clean. 6. Connect the hose and check for leaks. Risk of scalding . Allow the detergent solution to cool down. . Turn off the tap. What to do if... . . . . . . . . . . . . . . . . Water is leaking out. . Attach/replace the drainage hose correctly. . Tighten the screw connection of the supply hose. No water supply. Detergent not dispensed. . Start/Pause not selected? . Tap not turned on? . Filter blocked? Clean the filter a page 11. . Supply hose kinked or trapped? Washing machine door cannot be opened. . Safety function active. Programme termination? a page 4. . (Rinse Stop = no final spin) selected? ....page 3,4. . Can be opened by emergency release only? a page 13. Programme does not start. . Start/Pause selected? . Washing machine door closed? Detergent solution does not empty. . (Rinse Stop = no final spin) selected? a page 3,4. . Clean the detergent solution pump a page 11. . Clean the waste pipe and/or drainage hose. Water not visible in the drum. . Not a fault -water below the visible area. Spin result not satisfactory. Laundry wet/too damp. . No fault -the unbalanced-load detection system interrupted spinning, uneven laundry distribution. Distribute large and small items of laundry evenly in the drum. . (Less Ironing) selected? a page 5. . Speed selected too low? a page 5. Drum spins gently several times. . Not a fault -unbalanced-load detection system is adjusting the imbalance. Residual water in the compartment 0 for care products. . Not a fault -the action of the care product is not affected. . Clean the insert if necessary a page 10. Odour formation in the washing machine. . Run programme E Cottons 90 °C without laundry. Use standard detergent. t (Wash) display lamp flashes. Detergent may be leaking out of the detergent drawer. . Too much detergent used? Mix 1 tablespoon of fabric softener with . litre of water and pour into compartment II (not with outdoor or down fabrics). . Reduce the detergent dosage for the next wash cycle. Loud spinning, vibrations and .wandering. during the spin cycle. . Ar...
Dieses Handbuch ist für folgende Modelle:Waschmaschinen - WM12P160ME/03 (1.95 mb)