Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
Suitable descalers can be obtained via our website or from our after-sales service (.. page 13). Instructions in the display panel depending on model .. flashing Close the washing machine door properly; laundry may be caught. ..:...., .... Open the tap completely, supply hose kinked or trapped; Clean the filter .. page 11, water pressure too low. ..:.... Detergent solution pump blocked; Clean the detergent solution pump .. page 11. Drain hose/waste pipe blocked; Clean the drain hose on the siphon .. page 11. ..: .... Water in the base tub, appliance leaking. Call the after-sales service. Other displays Switch off the appliance, wait for 5 seconds and switch it back on. If the display appears again, call the after-sales service .. page 13. . Risk of electric shock. Disconnect the mains plug. . Risk of explosion. No solvents. 11 Information about blockages Detergent solution pump Turn the programme selector to Off and disconnect the mains plug. 1. Open and remove the service flap. 2. Take the drain hose out of the retainer. Remove the sealing cap, allow the detergent solution to flow out. Push the sealing cap back on. 3. Unscrew the pump cover carefully (residual water). 4. Clean the interior, pump cover thread and pump housing (the impeller in the detergent solution pump must be able to rotate). 5. Replace the pump cover and screw it on tightly. The handle points upright. Replace the drain hose in the holder. 6. Refit the service flap and close it. To prevent unused detergent from flowing straight into the drain during the next wash: Pour 1 litre of water into compartment II and start the Drain .. programme. Drain hose on the siphon Turn the programme selector to Off and disconnect the mains plug. 1. Loosen the hose clamp, remove the drain hose carefully (residual water). 2. Clean the drainage hose and siphon connecting piece. 3. Reattach the drainage hose and secure the connection with the hose clamp. Filter in the water supply Risk of electric shock Do not immerse the AquaStop safety device in water (contains electric valve). Reduce the water pressure in the supply hose: 1. Turn off the tap. 2. Select any programme (except Spin .. / Drain ..). 3. Press .. Start/Reload. Let the programme run for approximately 40 seconds. 4. Turn the programme selector to Off. Disconnect the mains plug. Clean the filter: 5. Disconnect the hose from the tap. Clean the filter with a small brush. and/or on standard and Aquasecure models: Remove the hose from the back of the appliance, remove the filter using pliers and clean the filter. 6. Connect the hose and check for leaks. Risk of scalding. . Allow the detergent solution to cool down. . Turn off the tap. What to do if... . . . . . . . . . . . . . . . . . Water is leaking out. . Attach/replace the drain hose correctly. . Tighten the screw connection of the supply hose. No water supply. Detergent not dispensed. . $ Start/Reload not pressed? . Tap not turned on? . Filter blocked? Clean the filter a page 11. . Supply hose kinked or trapped? Washing machine door cannot be opened. . Safety function active. Programme stopped? a page 4. . (Rinse hold = no final spin) selected? a page 3, 4. . Can be opened by emergency release only? a page 13. Programme does not start. . $ Start/Reload pressed or ....(Finished in) time selected? . Washing machine door closed? . Childlock active? Deactivate a page 5. Detergent solution does not drain. . (Rinse hold = no final spin) selected? a page 3, 4. . Clean the detergent solution pump a page 11. . Clean the waste pipe and/or drainage hose. Water not visible in the drum. . Not a fault -water below the visible area. Spin result not satisfactory. Laundry wet/too damp. . Not a fault -the imbalance monitoring system has interrupted the spin because the laundry is unevenly distributed. Distribute large and small items of laundry evenly in the drum. . S Reduced Ironing pressed? a page 5. . Speed selected too low? a page 5. The programme duration changes during the washing cycle. . Not a fault -the programme sequence is optimised for the relevant washing process. This can cause changes in the programme duration in the display panel. Repeated spin start-up. . Not a fault -imbalance monitoring system is equalising the imbalance. Residual water in the ~ compartment for care products. . Not a fault -the action of the care product is not affected. . Clean the insert if necessary a page 10. Odour formation in the washing machine. . Run the Cottons ..F 90 °C programme with the washing machine empty. Use standard detergent. Status indicator... flashing. Detergent may escape from the detergent drawer. . Too much detergent used? Mix 1 tablespoon of fabric softener with . litre water and pour the mixture into compartment II. (Not for outdoor textiles or those made with down.) . Reduce the amount of detergent for the next wash cycle. Pronounced generation of noise, vibration and .wandering. during the spin cycle. . Are the appliance feet fixed? Secure appliance fee...
Dieses Handbuch ist für folgende Modelle:Waschmaschinen - WAS28462GB/15 (2.34 mb)
Waschmaschinen - WAS28462GB/23 (2.34 mb)
Waschmaschinen - WAS28462GB/38 (2.34 mb)