Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
If it is necessary, however, proceed according to the descaling agent manufacturer's instructions. Suitable descalers can be obtained via our website or from our after-sales service (.. page 13). Information on the display panel model-dependent ....flashing Close the washing machine door properly; laundry may be caught. ..:...., .... Open the tap completely, supply hose kinked or trapped; Clean the filter .. page 11, water pressure too low. ..:.... . Detergent solution pump blocked; Clean the detergent solution pump .. page 11. . Drainage hose/waste pipe blocked; Clean the drainage hose at the siphon .. page 11. ..: .... Water in the base tub, appliance leaking. Call the after-sales service. .. Childproof lock activated: to deactivate .. page 5. Other displays Switch off the appliance, wait for 5 seconds and switch it back on. If the display appears again, call the after-sales service .. page 13. . Risk of electric shock! Disconnect the mains plug. . Risk of explosion! No solvents. 11 Information about blockages Detergent solution pump Turn the programme selector to Stop (Off) and disconnect the mains plug. 1. Open and remove the service flap. 2. Take the drainage hose out of the holder. Remove the sealing cap, allow the detergent solution to flow out. Push the sealing cap back on. 3. Unscrew the pump cover carefully (residual water). 4. Clean the interior, pump cover thread and pump housing (the impeller in the detergent solution pump must be able to rotate). 5. Replace the pump cover and screw it tightly in place. The handle points upright. Replace the drainage hose in the holder. 6. Refit the service flap and close it. To prevent unused detergent from flowing straight into the drain during the next wash: Pour 1 litre of water into compartment II and start the .. (Empty) programme. Drainage hose at the siphon Turn the programme selector to Stop (Off) and disconnect the mains plug. 1. Loosen the hose clamp, remove the drainage hose carefully (residual water). 2. Clean the drainage hose and siphon connecting piece. 3. Reattach the drainage hose and secure the connection with the hose clamp. Filter in the water supply Risk of electric shock Do not immerse the HydroSafe safety device in water (it contains an electric valve). Reduce the water pressure in the supply hose: 1. Turn off the tap. 2. Select any programme (except for ../Centrif. adicional ....(Rinse/Spin)//.. (Empty)). 3. Press Inicio/Pausa+Carga (Start/Pause+reload). Let the programme run for approximately 40 seconds. 4. Turn the programme selector to Stop (Off). Disconnect the mains plug. Clean the filter: 5. Disconnect the hose from the tap. Clean the filter using a small brush. and/or for Standard and Aqua-Secure models: Remove the hose from the back of the appliance, Remove the filter using pliers and clean the filter. 6. Connect the hose and check for leaks. Risk of scalding! . Allow the detergent solution to cool down. . Turn off the tap. 12 What to do if... .. Water is leaking out. . Attach/replace the drainage hose correctly. . Tighten the screw connection of the supply hose. .. No water supply. Detergent not dispensed. . Inicio/Pausa+Carga (Start/Pause+reload) not pressed? . Tap not turned on? . Filter blocked? Clean the filter .. page 11. . Supply hose kinked or trapped? .. Washing machine door cannot be opened. . Safety function active. Programme stopped? .. page 4. . .. (Rinse stop = no final spin) selected? .. page 3, 4. . Can be opened by emergency release only? .. page 13. .. Programme does not start. . Inicio/Pausa+Carga (Start/Pause+reload) pressed or ....(Finished in) time selected? . Washing machine door closed? . Childproof lock active? Deactivate .. page 5. .. Detergent solution does not empty. . .. (Rinse stop = no final spin) selected? .. page 3, 4. . Clean the detergent solution pump .. page 11. . Clean the waste pipe and/or drainage hose. .. Water not visible in the drum. . Not a fault - water below the visible area. .. Spin result not satisfactory. Laundry wet/too damp. . No fault - the unbalanced-load detection system interrupted spinning, uneven laundry distribution. Distribute large and small items of laundry evenly in the drum. . .. Facil (Easy-Iron) selected? .. page 5. . Speed selected too low? .. page 5. .. The programme duration changes during the washing cycle. . Not a fault - the programme sequence is optimised for the relevant washing process. This can cause changes in the programme duration in the display panel. .. Spin cycle runs several times. . Not a fault - unbalanced-load detection system is adjusting the imbalance. .. Residual water in the .. com- partment for care products. . Not a fault - the action of the care product is not affected. . Clean the insert if necessary .. page 10. .. Odour formation in the washing machine. . Run the Resistentes/Algod. (Cottons) 90 °C programme without laundry. Use standard detergent. .. Status display.... flashes. Detergent may escape from the detergent drawer. . Too much ...