Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Anleitung Zusammenfassung
When the service flap is half full, close the pump cover and empty the service flap. Repeat the above steps until all the detergent solution has completely drained out. 3. Carefully unscrew the pump cover (residual water). 4. Clean the interior, pump cover thread and pump housing (the impeller in the detergent solution pump must rotate). 5. Replace the pump cover and screw it tightly in place. 6. Place the service flap back on and close. To prevent unused detergent from flowing straight into the drain during the next wash: pour 1 litre of water into compartment II and start the Abpumpen / Vidange (Drain) programme. Drainage hose at the siphon Turn the programme selector to Aus / Arret (Off) and disconnect the mains plug. 1. Loosen the hose clamp, carefully remove the drainage hose (residual water). 2. Clean the drainage hose and siphon connecting piece. 3. Reattach the drainage hose and secure the connection with the hose clamp. Filter in the water supply Risk of electric shock. Do not immerse the Aqua-Stop safety device in water (it contains an electric valve). Reduce the water pressure in the supply hose: 1. Turn off the tap. 2. Select any programme (except for Schleudern/Spulen / Essorage/Rincage (Spin/Rinse) // Abpumpen / Vidange (Drain)). 3. Select Start / Depart. Let the programme run for approximately 40 seconds. 4. Turn the programme selector to Aus / Arret (Off). Disconnect the mains plug. Clean the filter: 1. Depending on model: Disconnect the hose from the tap. Clean the filter using a small brush. and/or for Standard and Aqua-Secure models: Remove the hose on the rear of the appliance. Remove the filter with pliers and clean. 2. Connect the hose and check for leaks. – Risk of scalding. Allow the detergent solution to cool down. – Turn off the tap. 11 What to do if ... ..Water is leaking out. – Attach/replace the drainage hose correctly. – Tighten the screw connection of the supply hose. ..No water supply. Detergent not dispensed. – Start / Depart not selected? – Tap not turned on? – Filter blocked? Clean the filter ..page 10. – Supply hose kinked or trapped? ..Washing machine door cannot be opened. – Safety function active. Wait approx. 2 minutes. – Is Spulstop / Cuve pleine (Rinse Hold) (without final spin) selected? ..page 3, 4. ..Programme does not start. – Start / Depart selected? – Washing machine door closed? ..Detergent solution is not drained. – Is Spulstop / Cuve pleine (Rinse Hold) (without final spin) selected? ..page 3, 4. – Clean the detergent solution pump ..page 10. – Clean the waste pipe and/or drainage hose. ..Water not visible in the drum. – Not a fault -water below the visible area. ..Unsatisfactory spin result. Laundry wet/too damp. – Not a fault -the unbalanced-load detection system has cancelled the spin cycle because of uneven distribution of the laundry. Distribute small and large items of laundry evenly inside the drum. – Bugelleicht / Facile (Reduced Ironing) selected? ..page 5. – Selected speed too low? ..page 5. ..Spin cycle performed several times. – Not a fault -unbalanced load detection system adjusts the imbalance. ..Residual water in the compartment for care products. – Not a fault -the action of the care product is not affected. – Clean the insert if necessary ..page 9. ..Odour formation in the washing machine. – Run programme Koch/Buntwasche / Blanc/Couleurs (Cottons) 90 °C without laundry. Use standard detergent. ..Waschen / Lavage (Wash) display lamp flashes. Foam may be coming out of the detergent drawer. – Too much detergent used? Mix 1 tablespoon of fabric softener with . litre of water and pour into dispenser II (not for outdoor and down-filled textiles!). – Reduce the detergent dosage for the next wash cycle. ..Intense noise formation, vibrations and “walking” during the spin cycle. – Are the appliance feet fixed? Secure the appliance feet ..Installation instructions. – Transportation safety devices removed? Remove the transportation safety devices ..Installation instructions. ..Noises during spin and drain cycles. – Clean detergent-solution pump ..page 10. ..The indicator lights do not function during operation. – Power cut? – Fuses tripped? Reset/change the fuse. – If the fault occurs repeatedly, call the after-sales service. ..Programme sequence longer than usual. – Not a fault -unbalanced load detection system adjusts imbalance by repeatedly distributing the laundry. – Not a fault -foam detection system active -adds an additional rinse cycle. ..Detergent residues on the laundry. – Occasionally, phosphate-free detergents contain water-insoluble residues. – Select Schleudern/Spulen / Essorage/Rincage (Spin/Rinse) or brush out the laundry after washing. If you cannot correct a fault yourself (switching on/off) or a repair is required: – Turn the programme selector to Aus / Arret (Off) and remove the mains plug from the socket. – Turn off the water supply and call the after-sales service ..Installation instructions. 11What to do if ... ..Water is leaking...
Dieses Handbuch ist für folgende Modelle:Waschmaschinen - WAE24FU3CH/29 (2 mb)
Waschmaschinen - WAE24FU3CH/31 (2 mb)
Waschmaschinen - WAE24FU3CH/34 (2 mb)